Vitek VT-TSP8 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 64

background image

17

3.

An accurate temperature will not be read if the forehead of the detected person doesn’t
aim at the “Temp zone”.

4.

If the temperature is lower than the normal value, please move towards the temperature
measurement sensor (2

”

to 8

”

away from the temperature sensor) to get an accurate

reading.

5.

Please rest after strenuous exercise and then test the temperature. If there is sweat on the
forehead, please wipe it before testing temperature.

6.

The installation height shall fit the height of the detected people. Note that the
temperature measurement module shall not be higher than the height of the people
detected.

«
...
20
21
22
23
24
...
»

Содержание VT-TSP8

































































Отзывы:

Нет отзывов

Похожие инструкции для VT-TSP8

EF35mm f/1.4L II USM

Бренд: Canon Страницы: 2

Digital IXUS 980 IS

Бренд: Canon Страницы: 36

EF LENS TS-E24MM F/3.5L

Бренд: Canon Страницы: 19

Бренд: Canon Страницы: 14

1236B001 - EOS Digital Rebel XTi Camera SLR

Бренд: Canon Страницы: 2

Бренд: GE Страницы: 86

Бренд: Mahindra Страницы: 12

Бренд: Baumer Страницы: 2

Бренд: Digisol Страницы: 18

Бренд: Sandstrom Страницы: 16

Бренд: IP Camera Страницы: 37

ATLONA Captivate AT-CAP-FC110

Бренд: Panduit Страницы: 24

Бренд: 70mai Страницы: 150

Бренд: Zee Страницы: 13

Бренд: Qvis Страницы: 23

Бренд: Casio Страницы: 112

Бренд: Grandstream Networks Страницы: 26

5.1 Megapixels Digital Camera

Бренд: Polaroid Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды