4
ENGLISH
•
Do not repair the unit by yourself. If there are
any damages in the unit, apply to the autho-
rized service center.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE USING THE UNIT FOR THE FIRST
TIME
After unit transportation or storage at low
temperature, it is necessary to keep it for at
least two hours at room temperature before
switching on.
•
Unpack the unit.
Disassemble and clean the juice extractor
before usage:
•
Remove the pusher (1) from the lid (3) feed-
ing chute (2).
•
Lift the bottom part of the locks (7) and
release the lid (3).
•
For easy removal of the grating filter (4), remove
the grating filter with the juice collector (5) hold-
ing the juice collector (5) and pulling it upwards.
•
Wash thoroughly and dry all the removable
parts that will contact products.
Note:
Be cautious when holding the grating fil-
ter (4) in your hands, as disc grating surface is
very sharp.
MAKING JUICE
Before the first plugging in make sure that the
operating voltage of the unit corresponds to the
voltage of your mains.
Fruit and vegetables meant for processing must
be fresh.
Before juice extracting wash fruit/vegetables,
remove inedible parts from vegetables or fruit,
such as stems, hard peel or stones, for example,
cherry or peach, cut them into pieces easily fit-
ting into the feeding chute (2).
•
Place the motor unit (8) on a dry, flat and
steady surface.
•
Before assembling the juice extractor make
sure that the operation mode switch is set to
the position «0» and the plug is not inserted
into the mains socket.
•
Place the juice collector (5) on the motor unit
(8) (pic. 1)
•
Install the grating filter (4) into the juice col-
lector (5) (pic. 2).
Attention!
Do not use juice extractor if you find mechan-
ical damages of the grating filter (4).
•
Install the lid (3) on the juice collector (5) and
fix it with the locks (7) (pic. 3)
•
Install the pulp container (10) in its place
(pic. 4).
•
Put the corresponding bowl under the juice
draining spout (6) (pic. 5)
•
Make sure that the juice draining spout is in
the lower position and the mark «
» matches
the mark «
» on the juice collector (5).
•
Insert the power plug into the mains socket.
•
Switch the juice extractor on by setting the
switch (9) to the position «I» (low speed), «II»
(high speed) or to the position «P» (pulse mode).
Notes
:
Low speed «I»
is intended for extracting juice
from soft vegetables/fruits, such as toma-
toes, ripe pears, strawberries, oranges, plums,
grapes, pumpkins, onions, cucumbers etc.
High speed «II»
is intended for extracting juice
from hard vegetables/fruits, such as artichoke,
carrots, apples, pepper, beet, potatoes, pine-
apples, vegetable marrows, celery, spinach, dill,
leek etc.
Pulse mode
«Р»
is intended for short time oper-
ation.
Attention!
To avoid stopping of grating filter (4) and
jamming of motor during processing viscous
or quite hard foods, it is recommended to
use the high speed «II» mode of juice extrac-
tor operation.
•
The unit will be switched on only if all the
removable parts are installed properly, and
the lid (3) is fixed with the locks (7).
•
Feed fruit/vegetable pieces into the lid (3)
feeding chute (2), only when the grating filter
(4) is rotating.
•
Put vegetables or fruits cut beforehand grad-
ually into the lid (3) feeding chute (2) and push
them gently with the pusher (1). Do not press
on the pusher (1) too hard as it can lead to
decrease of juice amount as well as to grating
filter (4) rotation stopping. The slower is the
fruit and vegetables processing, the higher is
the juice extraction rate.
•
Do not put your fingers or any other foreign
objects into the lid (3) feeding chute (2).
•
During operation check the grating filter (4)
periodically for obstruction of the mesh with
pulp, if necessary wash the grating filter (4);
before removing the grating filter, switch the
juice extractor off and unplug it.
VT-3655.indd 4
04.02.2015 12:01:20
