5
ENGLISH
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
USING THE HAIR CLIPPER
–
After unit transportation or storage at low
temperature, it is necessary to keep it for at
least three hours at room temperature before
switching on.
–
Remove all stickers and packaging elements
that can prevent unit operation.
Blades
–
If the blades have been removed for clean-
ing or replacement, install them back to their
places and tighten the fastening screws. The
unit’s design makes it unnecessary to level
the blades after installing them.
Lubricating oil
–
To maintain the unit in a good condition, you
should lubricate the blades regularly. Do not
use vegetable oil or oil that includes solvents.
Solvents are subjected to evaporation, and
the remaining thick oil can slow down the
upper blade (4) moving speed.
–
To lubricate the blades, use any special oil
for hair clipper blades (Oster, Moser, Dewal).
Taper lever (2)
–
The taper lever (2), that moves the lower
blade (3), is located under the thumb (if you
are right-handed). When cutting hair you can
move the blade, pressing the lever (2), thus
adjusting the cutting length without usage
of the attachment combs. In the upper lever
position, haircut will be the shortest one. In
the down lever position the cutting length is
approximately the same as with the 3 mm
attachment comb (6) usage. Changing the
position of the lever while cutting hair, you can
select the necessary length of the hair to cut.
–
If hair is jammed in the blades (3, 4) while cut-
ting, move the lever (2) from the upper posi-
tion to the down position several times, so you
can release the jammed hair without removing
the blades.
–
When the hair clipper is switched on, move the
lever several times from the upper position to
the lower position, this way you can remove
the cut-off hair from the blades.
–
If the unit pulls hair while cutting, it means that
the blades (3, 4) became blunt, replace them
with new ones.
Instructions on hair cutting
•
Hair should be clean and dry while cutting.
•
Insert the power plug into the mains socket.
•
Before cutting hair, switch the unit on by mov-
ing the power switch (1) to the position «I» and
make sure that the hair clipper operates nor-
mally and the blades move smoothly. If there
is excess oil on the blades, remove it with a
dry cloth.
•
Constantly check the power cord, prevent it
from multiple twisting, regularly switch the
unit off and straighten the power cord.
•
Seat the person so that his/her head is
approximately at your eye level, cover the
person’s shoulders with a towel and set hair
with the comb (11).
Attention:
–
Always cut off a little amount of hair at a time.
If necessary you can always return to the
trimmed area for additional cutting.
–
The best haircutting results are reached on
dry hair, not wet.
–
Set the hair with the comb (11) to reveal
uneven locks.
–
It is better to leave longer hair after cutting for
the first time.
–
After learning your clipper better, you will be
able to arrange your hair in any style you need.
Attachment combs
The length of hair depends on the attachment
comb:
–
Attachment comb (6): hair length 3 mm
–
Attachment comb (7): hair length 6 mm
–
Attachment comb (8): hair length 9 mm
–
Attachment comb (9): hair length 12 mm
Set the attachment upper part on the blade and
press it until click. To remove the attachment
comb, press the clamp and remove the attach-
ment.
Step one
Set the 3 mm attachment comb (6) or 6 mm
attachment comb (7). Switch the unit on using
the power switch (1), setting it to position «I».
Hold the unit with the blades pointed upwards.
Start haircutting from the beginning of the hair
VT-2511.indd 5
05.09.2017 18:05:37
