Vitek VT-1751 BK, Инструкция по эксплуатации

Страница: 5 / 40

5
ENGLISH
switch on «ECO» mode (see switching on «ECO»
mode above).
•
After the finishing the operation of the fan heat-
er press the On/Off button (11), there will be a
long sound signal, and the time left before the
switching off (6 seconds) will appear on the dis-
play (3). After this time the unit will switch off.
Notes:
– While the first switching the heating ele-
ment burns, therefore occurrence of a small
amount of smoke or extraneous smell is pos-
sible, it is normal.
– The fan heater has “tip-over switch” (button
(9) on the lower lid of the unit body), so if you
lift the fan heater you’ll hear a distinctive click,
which indicates the normal operation of the
tip-over switch.
– Do not open windows or doors when the fan
heater is operating. There should be good
heat-insulation in the room; otherwise you will
not get the desired results, due to cold air flow.
Using the Remote control
Attention!
Functions of the buttons on the remote con-
trol fully correspond to the buttons on the
control panel.
– to replace the batteries open the battery com-
partment lid of the remote control by turning
the lid to «OPEN» position with a help of, for
example, a coin and remove old batteries,
then insert a new CR2032 battery.
– Close the battery compartment lid, matching
the arrow on the lid with a mark «OPEN»; turn
the lid to «CLOSE» position.
Function of automatic emergency switch-off
The fan heater is equipped with function of auto-
matic emergency switch-off.
If the unit starts overheating, automatic thermal
switch will be on.
– In this case the unit will switch off automatically.
– Remove the power cord (8) plug from the
socket.
– Make sure that the air inlet and outlet grids
are not blocked and nothing prevents air flow.
– Let the unit cool down for approximately 20
minutes before switching it on again.
– Plug the unit into the mains and switch it on
pressing the button (11). If the unit does not
switch on, it may mean that there are other
damages in the unit. In this case contact the
authorized service center for check or repair.
Cleaning and maintenance
•
Before cleaning the unit, switch it off by
pressing the button (11) and remove the
power cord (8) plug from the socket.
•
Do not use liquid detergents, abrasives and
any solvents, for example, acetone, to clean
the unit.
•
To avoid the risk of fire or electric shock pro-
vide that water or other liquid does not get
into the fan heater body.
•
Wipe the unit body with a slightly damp cloth,
then wipe it dry. To remove dust from the
grids use a vacuum cleaner with a corre-
sponding attachment.
•
After cleaning put the fan to a dry cool place
away from children for storage.
•
Before starting the unit, check the technical
condition of the unit, the power cord plug and
the power cord (8) insulation.
Cleaning the filter (6)
– Remove the inlet filter grid (7).
– Remove the filter (6), wash it and dry.
– Install filter (6) back in its place.
– Install the inlet filter grid (7) back in its place;
make sure that all the clamps go to their cor-
responding openings.
ATTENTION! Portable electric fan heaters are
intended for additional rooms heating. They are
not meant for operation as main heating units.
Technical specifications
Power supply: 220-240 V, ~ 50 Hz
Power: 2000 W
Heating area: up to 20 m
2
The manufacturer preserves the right to change
the specifications of the unit without a prelimi-
nary notification
Unit operating life is 5 years.
Guarantee
Details regarding guarantee conditions can be ob-
tained from the dealer from whom the appliance was
purchased. The bill of sale or receipt must be produced
when making any claim under the terms of this guar-
antee.
This product conforms to the EMC-
Requirements as laid down by the Council
Directive 89/336/EEC and to the Low Voltage
Regulation (73/23 EEC)
VT-1751 IM.indd 5 04.06.2012 14:11:11