manualshive.com logo in svg

Vitec Multimedia 17245, Руководство пользователя

Поделиться
Скачать
Vitec Multimedia 17245 Скачать руководство пользователя страница 41

 

MGW Diamond

 

Multi-Channel HEVC and H.264 Portable Encoder 

 

User Manual, Version 1.6 

41 

 

Error Correction Settings 

Zixi™ 

 

The Zixi™ protocol supports two modes: VITEC Playout / Zixi™ Broadcaster Server, and Point

-to-

point streaming directly from the VITEC encoder to the VITEC decoder appliance. Zixi™ sessions 

can be protected by a password. Protected sessions ensure that only authorized 
encoders/decoders participate in these sessions.   

•

 

Password

: If a password was set on Zixi™ server, enter the password for streaming. If 

no password was set on the VITEC Playout Server or Zixi™ server, no password is 

required. When connecting directly (point-to-point) to a decoder, a password is not 
applicable. 

•

 

Latency:

 Enter a latency value in milliseconds to be used for correcting errors. The 

minimal latency to be used must be higher than 3 times the RTT value (Round Trip Time) 

between the encoder and the targeted decoder. RTT value is available in Zixi™ Channel 
Statistics window after the Zixi™ channel has been started. Additionally, higher latency 

increases tolerance to network errors (range 0-6000 milliseconds). The actual error 
correction rates depend also on the stream bit-rate. On average, 500ms latency yields 
protection of up to 6% of network errors. 6000ms latency yields protection of up to 30% 
of network errors.   

 

•

 

When using a Zixi latency lower than 500ms, FEC data protection is enabled resulting in an increased total output 
bitrate up to 50%. Ensure the transmission link bandwidth is dimensioned for such bitrate. 

•

 

If Zixi latency is set to 0, no data protection is achieved. Use this value to analyze the quality of your transmission 
link. Transmission link statistics are reported within the Zixi Statistics Channel (Dashboard). 

Check the Zixi™ Statistic information window to monitor the packet loss of the 

transmission link used and set the latency accordingly. 

•

 

Enable ABR (Adaptive Bitrate)

: Select the check box to allow either VITEC decoder or 

the Playout Server/ Zixi™ Broadcaster to automatically change the encoding bit

-rate while 

streaming. When selected, the channel total bit-rate will automatically be optimized, 
bas

ed on network performance and statistics from the Zixi™ stream recipient, to ensure 

smooth, artifacts-free playback. 

•

 

Minimum Bit-Rate: Set the minimum bit-rate allowed while in dynamic mode 

•

 

Maximum Bit-Rate: Set the maximum bit-rate allowed while in dynamic mode. 

•

 

Enable Failover

: Select the check box to allow MGW Diamond Encoder to switch over a 

secondary VITEC Playout/ Zixi™ Broadcaster Server when the primary server is no more 

reachable. 

•

 

Set the IP address of the Zixi™ broadcaster failover server 

 

•

 

Set the Port address of the Zixi™ broadcaster failover server. 

 

Содержание 17245




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды