8
DE5458
F. MCT-211
(Fig. 27) This unit
is a waterproof,
wrist-worn
PowerCode transmitter, that
can be enrolled to perform
emergency or non-alarm
function.
Figure 27.
MCT-211
3.10 Mounting the RS232 Module
The control panel can be equipped with an optional RS232
module for serial data interchange with a local computer. If
this module is not supplied, a special plastic cap blocks the
niche designed to accommodate the module.
The following instructions are useful when adding the
RS232 module to an already installed PowerArt™ system:
A.
Detach the cabinet from the bracket (see Para. 5.1)
B.
Remove the factory installed plastic cap by sliding it out
along the grooves as shown in Figure 28.
Figure 28.
Removing the Cap from the RS232 Niche
C.
Align the RS232 module with the grooves and the
module catches as shown in Figure 29.
D.
Push the module all the way in, making sure that the
4-pin socket mates with the 4-pin header at the bottom
of the unit.
Note:
When the module is properly seated, the module
catches pushed aside during insertion will spring back
into place above the top edge of the module.
E.
Prepare an RS-232 flat modular cable and terminate it
with a 6-position RJ-11 plug at the PowerArt™ end.
Terminations at the computer’s end may vary.
F.
Mate the plug with the RJ-11 socket and bend the cable
backward to route it out via the wiring channel.
G .
Re-attach the control panel to the bracket, as
instructed in Para. 3.6.
Figure 29.
Inserting the RS232 Module
3.11 Installing an Optional X-10 Siren
If you need a “wireless” external siren, you may install an
X-10 siren module which is triggered by a signal transmitted
via the built-in electrical wiring of the protected site. This
siren can replace the regular external siren or complement it
without laying out additional wires. Of course, such a siren
can be used only in conjunction with an optional power-line
interface module.
The X-10 siren is ready to function upon connection to an
electrical power outlet, without re-programming the Power-
Max. You only have to set the HOUSE CODE and the
UNIT CODE selectors on the X-10 siren as follows:
House Code:
Set this selector to the letter that follows, by
alphabetical order, the letter that you programmed as a
house code for the protected premises. For example, if the
programmed house code is “
J
”, set the siren house code
selector to “
K
”.
Note:
If the programmed house code letter is “
P
” (which is
the last programmable letter), select “
A
” for the siren.
Unit Code:
The siren will function only if you set the unit
code selector to “
1
”.
4. TESTING PROCEDURES
4.1 Preparations
Make sure all windows and doors are closed. If all zones
are secured (undisturbed), the display should read:
R E A D Y
H H : M M
If the system is “NOT READY”, query the control panel by
pressing the <
SHOW/OK
> button repeatedly. The
source(s) of the problem(s) will be displayed and read
aloud. Take the necessary measures to eliminate the
problem(s) before testing the system (see 4.2 below).
4.2 Diagnostic Test
To verify proper function of all detectors in the system, a
comprehensive diagnostic test is required. To perform this
test, you must access item No.
8
in the installer’s menu
the same way as you did when you programmed the
control panel:
A.
Click the <
NEXT
> button until the display reads:
I N S T A L L E R
M O D E
B.
Click <
OK
> to select the installer’s menu. The control
panel will prompt you for the installer code.
C.
Enter the valid installer code (
9
#
9
#
9
#
9)
or the new
installer code that you already programmed. The
“Happy Tune” (- - - ––––) will sound if the code is
correct and the display will change to:
1 . N E W I N S T L C O D E
D.
Click <
NEXT
> or <
BACK
> until the number and name
of the desired mode are displayed:
8 . D I A G N O S T I C S
E.
Carry on as in Section 9 of the programming guide.
4.3 Keyfob Transmitter Test
Initiate transmission from each transmitter enrolled as a
keyfob unit (according to the list in Table A2, Appendix A).
Use each transmitter to arm the control panel AWAY and
immediately disarm it.
Содержание POWERART
Страница 15: ...DE5458 15 ...
