background image

22

VISION RF PAGING SYSTEM USER’S GUIDE

TROUBLESHOOTING

TRANSMITTER BATTERY DIED.

If you don’t see any icons on the LCD, put in a fresh AAA battery.  To Dis-

arm when your pager is not working, simply press Unlock on your factory 

remote, or use Manual Disarming (pg.5 in the 1480/1460 Owner’s Guide).

CAN’T MAKE SIREN TRIGGER AFTER ARMING.

• 

Did you use Sensor Bypass Arming?  That would explain why the shock 

sensor is not triggering the siren.  (See page 8 in this manual, and page 

3 in the 1480/1460 Owner’s Guide.)

• 

Did you use Button-II Silent Mode Arming?  (See page 7.) 

• 

If used Normal Arming (Button-I), did you hear a single chip when you 

Armed?  If not, you may not have Armed the system at all!  You cannot 

Arm

 with the pager when the Ignition is ON and “IG Protect Mode” is en-

abled.  (See pages 7 & 12 in the 1480/1460 Owner’s Guide.)  Also note that 

some cars won’t allow you to use Lock on the factory remote to Arm while 

the Ignition is ON, regardless of the 1480/1460’s programmed setting.

WARNING CHIRPS GO OFF FOREVER, CAN’T DISARM WITH REMOTE.

If you are using an Ultrasonic Sensor along with the 1480/1460’s shock 

sensor, it is likely that the two sensors were installed too close together.  

They must be separated by more than 30cm (1 ft.) or interference will 

cause a continual false triggering of the siren.  

FULL SIREN GOES OFF WITH ONLY LIGHT IMPACT TO THE VEHICLE.

If you do not have an Ultrasonic Sensor installed, try adjusting sensitiv-

ity of your shock sensor or mounting it in another location.  If that doesn’t 

work, you will need to snap open the housing of the shock sensor and 

verify if the suspended reflector has been jolted out of position (see page 

17 in the 1480/1460 Installation Guide).

I ONLY DRIVE MY CAR ONCE A MONTH, WILL MY CAR BATTERY DIE?

Assuming you run the engine long enough to fully charge your car’s bat-

tery, then it will depend on what electronic devices you have installed.  

The current consumption of the 1480S & 1460S is very low, so starting 

the  engine  once  every  3  weeks  should  be  fine.    But  with  the  1480B  or 

1460B, consider running the engine every couple weeks to charge your 

car’s battery.  Or consider purchasing a 3rd party solar 12-volt trickle 

charger (noting that our company does not sell or support these devices, 

nor do we recommend which model/brand to buy).

Содержание TR537S





























Отзывы: