Vision Fitness T60 Скачать руководство пользователя страница 21

Страница: 21 / 59

6.5 ERROR MESSAGES ON THE CONSOLE

Class

Level

Error

Code

Description

Conditioned

Solution

0140

Incline motor operation fail.

When the elevation is supposed to move,

it does not. When the error happens, the

elevation will be locked. The command

initialize is needed to unlock.

1. Check connection of the elevation motor.

2. MCB LED check.

3. Replace the incline motor.

01A0

Incline motor disconnection.

When the elevation position cable is not

connected.

1. Check connection of the elevation motor.

2. MCB LED check.

3. Replace the incline motor.

01A4

Main motor U phase

disconnection.

Main motor U phase wire disconnected. 1. Check the connection of the motor.

2. Replace the motor.

3. Replace the MCB.

01A5

Main motor V phase

disconnection.

Main motor V phase wire disconnected.

1. Check the connection of the motor.

2. Replace the motor.

3. Replace the MCB.

01A6

Main motor W phase

disconnection.

Main motor W phase wire disconnected. 1. Check the connection of the motor.

2. Replace the motor.

3. Replace the MCB.

01A8

Main motor over current.

Main motor over current (7 Amps)

1. Check the connection of the motor.

2. Check the condition of the deck / belt.

3. Do an amp check.

01AB

Inverter error.

Internal error of the inverter.

1. Check the MCB errors.

2. Replace the MCB.

01AD

Inner electron over

temperature: motor over

When it thinks the user is over 130 KG

(350 lbs) making the motor overload.

Check the condition of the deck / belt, replace

as needed.

02A0

Main motor fail.

The belt does not move when it is

supposed to move.

1. Check the power input connections.

2. Do a resistance check on the motor,

replace if needed.

3. MCB replacement.

02A1

Over AC power input voltage. Power input voltage over range.

Check the power input connections.

02A2

Over / low DC bus voltage.

Power input voltage over range.

Check the power input connections.

02A8

Inverter circuit of motor driver

failed.

Motor resistance is closed.

Do a resistance check on the motor, replace if

needed.

02AD

MCB over temperature.

1. Check the MCB temperature.

2. Check the cooling fan for function.

3. Replace the MCB.

02B5

Inverter senses the normal

rated current is over 150% for

60 seconds.

Inverter senses the normal rated

current is over 10.5 Amps for at least 60

seconds.

Check the connection of the motor.

02B6

Speed up is over current.

Software error.

Check the condition of the deck / belt, replace

as needed.

02B7

Speed down is over current. Software error.

Replace the MCB.

02B8

Running status over current. Software error.

1. Check the connection of the motor.

2. Check the condition of the deck / belt,

replace as needed.

02B9

The inner memory IC data

write error.

MCB failure.

Replace the MCB.

02BA

The inner memory IC data

read error.

MCB failure.

Replace the MCB.

02BC

Ground connection of fuse

error.

MCB failure.

Replace the MCB.

02BD

Inverter hardware interrupt

error.

MCB failure.

Replace the MCB.

04A0

No communication response. Digital Communication failed.

1. Check the console cable connection at the

MCB and UCB.

2. Check the MCB LEDs.

3. Replace the console cable, MCB, or UCB.

CHAPTER 6: TROUBLESHOOTING

Содержание T60




























































Результаты поиска

Содержание T60

Отзывы:

Похожие инструкции для T60

Бренды по названию

Популярные бренды

Vision Fitness T60, Руководство по обслуживанию

Результаты поиска

Содержание T60

Отзывы:

Похожие инструкции для T60

Бренды по названию

Популярные бренды