Vision Fitness T60 Скачать руководство пользователя страница 13

Страница: 13 / 59

4.3 WORKOUT OVERVIEW

WORKOUT OVERVIEW

PROGRAM

DESCRIPTION

DEFAULT

TIME

PROMPT

INPUT

PROGRAM

CONTROL

QUICK START

Quick Start is the fastest way to begin exercising and

bypasses the setup prompts. After pressing the Quick Start

key, a constant level workout begins, and the speed and

incline do not change automatically.

N/A

MANUAL

Manual is a constant effort workout in which the user can

change incline or speed at any time.

20 Min

Time, Weight

N/A

INTERVAL

Intervals is periods of intense aerobic exercise separated

by periods of lower intensity exercise. At any point during

the workout, the user can change the settings of the current

speed.

20 Min

Level, Time,

Weight

Elevation

GOAL+

TIME GOAL

This workout sets duration as the workout goal. Once the

duration objective is met, the workout goes into a cool down

phase.

20 Min

Time, Start,

Incline, Start

Speed, Weight

N/A

DISTANCE

GOAL

This workout is designed to build endurance in a certain

distance. Once the objective is met, the workout

automatically goes into a cool down phase, and ends

afterward.

N/A

Distance, Start

Incline, Start

Speed, Weight

N/A

CALORIES

GOAL

This workout is designed to burn a certain number of

calories in the selected time duration. Once the objective is

met, the workout automatically goes into a cool down phase

and ends afterwards

N/A

Calories, Start

Incline, Start

Speed, Weight

N/A

RANDOM

Random crates a random terrain patter of hills and valleys

that varies with each workout.

20 Min

Time, Weight

Elevation

HEART

RATE+

TARGET

Target HR is a higher intensity workout for more fit users

emphasizing cardiovascular benefits. The user must wear

a heart rate chest strap, or keeps hands on the contact

heart rate grips continuously. The program adjusts the

intensity level based on the actual heart rate to maintain the

rate at 80 percent of theoretical maximum.

20 Min

Age, Heart

Rate, HR

Control, Max

Speed or Max

Incline, Time,

Weight

Speed or

Elevation

WEIGHT

LOSS

Weight loss is a low intensity workout for burning the body's

fat reserves. The user must wear or a heart rate strap or

keep hands on the contact heart rate grips continuously.

The program adjusts the intensity level based on the actual

heart rate to maintain a rate of 65 percent of the theoretical

maximum. Also uses Body Mass Index (BMI) to measure

your body composition.

20 Min

Age, Heart

Rate, HR

Control, Max

Speed or Max

Incline, Time,

Weight, Height

Speed or

Elevation

FITNESS TEST

Vision Treadmills offer the Gerkin Fitness Test. The Gerkin

firefighter protocol was developed by Dr. Richard Gerkin of

the Phoenix (Arizona) Fire Department. It is a sub-maximal

graded treadmill evaluation used by many fire departments

across the US to assess the physical condition of the

firefighters. The test requires constant monitoring of the

user's heart rate so the use of a telemetric chest strap is

highly encouraged.

N/A

CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION

Содержание T60




























































Результаты поиска

Содержание T60

Отзывы:

Похожие инструкции для T60

Бренды по названию

Популярные бренды

Vision Fitness T60, Руководство по обслуживанию

Результаты поиска

Содержание T60

Отзывы:

Похожие инструкции для T60

Бренды по названию

Популярные бренды