Vision & Control Vicosys 5400 Скачать руководство пользователя страница 23

Страница: 23 / 64

vicosys

5400

Technical Data

999.994.729.10-en-2.3

Parameter

Min

Nom

Max

Baut rate

9.6 kBit/s

115.2 kBit/s

Protocol

Internal protocol

Number of bits

Number of stop bits

Parity

none

Flow control

none

Galvanic decoupling

non-existent

Factory setting

5.3.3 USB interfaces

NOTICE

Overheating due overload

•

Each USB port can deliver a maximum output current of 900 mA.

•

The maximum output current for USB port 1 to 4 must not exceed 1500

mA.

ADVICE

Data loss due to incorrect disconnecting of devices!

•

Always unmount USB storage devices before switching off or

disconnecting.

•

Unmount in vcwin pro:

Using the instruction

External Storage Device - Unmount USB Device

Содержание Vicosys 5400

































































Результаты поиска

Содержание Vicosys 5400

Отзывы:

Похожие инструкции для Vicosys 5400

Бренды по названию

Популярные бренды

Vision & Control Vicosys 5400, Инструкция по эксплуатации

Результаты поиска

Содержание Vicosys 5400

Отзывы:

Похожие инструкции для Vicosys 5400

Бренды по названию

Популярные бренды