ViscoTec Preeflow eco-CONTROL EC200-B Скачать руководство пользователя

Страница: 33 / 36

Version 1.9

33 / 35

eco-CONTROL EC200-B

Operation and maintenance instructions

Troubleshooting / maintenance

Troubleshooting

Maintenance

The Dosing control can be regarded as maintenance-free. Do not use any aggressive

solvents or cleaners for cleaning, only a damp cloth. Unplug the unit from the mains

before doing any cleaning.

Error

Possible cause

Correction

Dosing system cannot be

operated, no display.

no dispenser connected

connect dispenser (ensure that

the mains plug has been

removed beforehand)

Power supply off

switch on

Dosing program cannot be

saved, only program 00 is

offered

No chipcard inserted, or not

formatted

Insert / format the chipcard

Error messages

Overcurrent monitoring

Dispenser components do not

run smoothly due to hardened

medium or as a result of dry

running.

Dismantle and clean the

dispenser, replace the stator if

necessary.

See the operating instructions for

the dispenser.

Level of medium critical

Not enough medium in the

supply tank

Fill up with the medium. If the

error message remains, check

the sensor and sensor input, if

applicable, brief "emergency

operation" without level

monitoring.

Check the compressed air Compressed air too little, or

switched off

Check / switch on the

compressed air

Tolerance range set too small

Set the tolerance range to be

larger, see (5.10.6)

Primary pressure monitoring

has been switched on and the

dummy plug has not been

inserted into the sensor input.

Insert the dummy plug or turn off

the primary pressure monitoring,

see (5.10.10)

Содержание Preeflow eco-CONTROL EC200-B





































Результаты поиска

Содержание Preeflow eco-CONTROL EC200-B

Отзывы:

Похожие инструкции для Preeflow eco-CONTROL EC200-B

Бренды по названию

Популярные бренды

ViscoTec Preeflow eco-CONTROL EC200-B, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Preeflow eco-CONTROL EC200-B

Отзывы:

Похожие инструкции для Preeflow eco-CONTROL EC200-B

Бренды по названию

Популярные бренды