ViscoTec Preeflow eco-CONTROL EC200-B Скачать руководство пользователя

Страница: 24 / 36

24 / 35

Version 1.9

eco-CONTROL EC200-B

Operation and maintenance instructions

• Press the

Navi wheel

, display

, changes to

Off

Protection active

appears in the status bar.

• Select and confirm the password (code).

• Set the password by turning* the

Navi wheel

• Press the

button and confirm, password protection has

been activated.

* Dynamic behaviour: The faster it is turned, the quicker the range of numbers

changes.

Note:

If no further buttons are pressed, the password protection blocks the controller

after 30 seconds.

Releasing the controller

(if password protection has been activated)

The start screen is shown when it is in the blocked state.

Display 42 appears if a button is pressed.

• Select the correct password by turning the

Navi wheel

and

confirm it by pressing, then the start screen appears.

Note:

If no further buttons are pressed, the password protection blocks the controller

after 30 seconds.

Turning off password protection

Release the controller as described above.

• Press the

PRG

key,

system selection menu

display 2 appears.

• Select and confirm

Administration

, the

Administration

menu, display 25 appears.

• Select

Password protection

, display 41 appears.

• Press the

Navi wheel

, display

Off

, changes to

Protection inactive

appears in the status bar.

• Press the

button and confirm, password protection has

been deactivated.

Esc

Password protection

protection inactive

Code

5000

Esc

Enter password

Schutz inaktiv

Code?

5000

Start/stop
Time program
Calibration auto
Calibration manuel
Teach in function
Administration

Quantity program

10 47h

Fr 18.03.11

Service

Esc OK

Change program
Tolerance of pressure
Password protection
Analog input
Adjust time

Select program

Esc

Password protection

protection inactive

Code

5000

Содержание Preeflow eco-CONTROL EC200-B





































Результаты поиска

Содержание Preeflow eco-CONTROL EC200-B

Отзывы:

Похожие инструкции для Preeflow eco-CONTROL EC200-B

Бренды по названию

Популярные бренды

ViscoTec Preeflow eco-CONTROL EC200-B, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Preeflow eco-CONTROL EC200-B

Отзывы:

Похожие инструкции для Preeflow eco-CONTROL EC200-B

Бренды по названию

Популярные бренды