Virutex TM33W, Руководство по эксплуатации, Страница: 11 / 48

11
The laser guide has an inertia switch, so it is only activated
when the saw blade is turning.
The laser guide also includes an On/
off switch T1 (Fig. 22) to activate or
deactivate it. The switch must be turned
to ‘Off’ for cutting on the upper table.
The electric tool is supplied as standard with a warning
sign in Spanish R (Fig. 18).
Before starting for the first time, stick the attached
label written in your language over the warning sign.
7. APPLICATIONS OF MITERING, INTENDED
CONDITIONS OF USE
This machine enables you to cut pieces of wood, plastic
and aluminium angles efficiently and precisely.
The rule on the machine is grooved which allows you
to quickly position a wood R2 support to prevent any
splintering of the material being cut (Fig. 18). Use of
the knobs is strongly recommended when cutting fragile
or thin materials.
It is essential to use clamps (see section
10) for cutting aluminium angles, plastic
or long pieces (Fig. 20).
Do not start any cut until the blade has reached its full
speed of rotation.
7.1 CUTTING AT 0° x 0°
Continue as shown in (Fig. 18), making the cut with the
assistance of the laser guide. The wood support stop is
fitted with a millimeter ruler S1 (Fig. 19) to facilitate
the cutting operation. The ruler marks the excess length
to be cut.
7.2 CUTTING AT 0° x 45°
Release handle D (Fig. 2), lower the head to the 45° stop
or any other intermediate angle as required, using the
angle indicator Z1 (Fig. 15); and tighten handle D in
the selected position.
7.3 CUTTING AT 45° x 0°
Press down lever E2 (Fig. 5) and turn the plate towards
the left or right until the index marks 45º or any of the
standard positions (15º, 22º30', 30º, 45º).
Should you wish to make a cut that does not match
any of the plate's standard positions, push down lever
E2 (Fig. 3) and then push it towards trigger E3 (Fig. 3).
This will unlock the plate, enabling you to regulate
the exact angle you require. Then lock the plate using
knobs K (Fig. 3).
7.4 CUTTING AT 45° x 45°
Press down lever E2 (Fig. 4) and turn the plate towards
the left until it locks into place at 45º. Loosen handle D
and lower the head to the stop at 45º or the intermediate
angle you wish. Lock it in place once again (Fig. 4).
The machine also enables you to tilt the head to any
position on the plate (only by turning it to the left).
Ensure that the moving arm is well secured
in position when mitering.
7.5 SPECIAL CUTS 200 x 45 mm
In the 0°x0° position this machine can make cuts up to
200 x 45 mm. For these cuts must be placed on the lower
table to do this, just fit supplements N2 ref. 3346388
supplements for 200 mm cuts (optional accessory) to the
bottom table and then the cut can be made as normal.
This is possible due to the retractable saw protector R
(Fig. 16) which retracts as the cut is made.
7.6 MULTIPLE CUTS
To make multiple cuts the length stop A1 must be insta-
lled and regulated to the required measurement (Fig. 5)
8. CUTS ON THE UPPER TABLE,
INTENDED CONDITIONS OF USE
(only with models TM33W)
The laser guide also includes an On/
Off switch T1 (Fig. 22) to activate or
deactivate it. The switch must be turned
to ‘Off’ for cutting on the upper table.
On the upper table only plastics and wood
can be cut, never aluminium or angles.
To use the machine in this cutting mode the lower cover
K1 (Fig. 6) should be positioned on the machine which
prevents any accidental contact of the saw disc under
the table. Fit the right-hand side of the fairing onto