VIRTUFIT Etappe 1, Руководство пользователя

Страница: 10 / 30

ENGLISH
EN
10
If the screen is unreadable or only parts of the image work, proceed
as follows:
• Remove the batteries and wait 15 seconds.
• Replace the batteries correctly.
Tips on using the battery
• Remove the batteries from the screen when they are empty or
when the device will not be used for a long period of time.
• Do not recharge, disassemble or dispose of batteries in fire.
• Pay close attention to the + and - when inserting the batteries.
• It is recommended to use alkaline batteries, they have a longer
life than normal batteries.
• Batteries should be replaced when the display loses brightness
or stops showing.
Battery replacement
• If the display is not accurate, it is recommended to replace the
batteries.
• Use 1 x 3V CR2032 battery for power.
4
Virtufit Etappe 1
NL
Opmerking:
1. Als u 4 minuten stopt met trainen gaat het trainingsscherm uit.
U kunt een willekeurige knop indrukken om uw trainingsscherm terug te krijgen en verder te gaan waar
u was gebleven. Uw trainingsgegevens staan nog steeds in het systeem.
(Als u de batterij vervangt zijn al uw instellingen wel weg.)
2. Geeft het display vreemde gegevens weer, installeer dan opnieuw de batterij en kijk of dit het probleem
op lost.
3. Batterij: 3V CR2032 (1 stuk). Om de batterij te vervangen:
HANDLEIDING VAN HET DISPLAY
1. Verwijder de schroeven van de batterij
houder.
2. Verwijder de batterij beschermkap.
3. Plaats de batterij op de aangegeven
plek.
4. Plaats de batterij beschermkap terug,
en schroef hem vast.
Batterij inbegrepen
TROUBLESHOOTING
The display does not show any values: Check that the sensor and
console cables are properly attached and undamaged. If this does not
solve the problem, contact the supplier.
Device squeaks: Check that all bolts and nuts are tight. If necessary.
Check whether the brake pad needs to be lubricated.
Ticking noise when pedalling: This may be caused by one of the
pedals. Remove the pedal(s) and mount it (them) correctly on the unit.
Tighten the pedal(s) firmly. If this does not solve the problem, contact
the supplier.
NOTE!
The "R" (right) pedal must be mounted clockwise and the "L"
(left) pedal must be mounted counter-clockwise.
Console does not work: If there is no signal when pedalling, check that
the cable is correctly connected.
Daily maintenance
• Clean and remove sweat and moisture after each use.
• Check that the unit is free of dust and dirt.
• Do not use aggressive cleaning agents and keep the device
away from moisture.
Semi-annual maintenance
• Inspect all bolts and nuts connected to the moving parts of the
unit. Tighten bolts and nuts as necessary and appropriate.
We recommend the following:
• Clean the unit after use.
• Use a dry cloth to clean the control panel and the areas around
the on/off switch.
• Use a soft, clean cloth and detergent to remove stubborn marks
and dirt from the unit.
• Store the unit in a safe, dry place away from heat and water.
CAUTION!
Repairs must be carried out by a professional technician,
unless otherwise specified by the supplier or manufacturer.
Cleaning
General cleaning of the unit will extend its life. Keep the appliance
clean by dusting it regularly. Regular maintenance will prolong the life
of your appliance and prevent injuries! For more information, please
visit https://www.virtufit.nl/service/faq/
CAUTION!
Wear clean shoes to reduce the risk of soiling the
machine. At least once a year, remove the cover to remove dust.
Lubricating the brake block
Use the enclosed bottle of silicone oil to lightly lubricate the brake
pad. This will reduce friction on the flywheel and provide a quieter
experience. When you begin to notice that the pad is becoming dry,
apply a little silicone oil again. Make sure the block does not get dry.
Battery
3V CR2032 BATTERIES
The display uses 3V CR2032 batteries, which are replaceable on the
back of the display. The batteries must be inserted correctly.