virtual access GW3330 Скачать руководство пользователя страница 176

Страница: 176 / 372

22: Configuring a WiFi connection

_______________________________________________________________________________________________________

_____________________________________________________________________________________________________

GW3300 Series User Manual

Issue: 1.7

Page 176 of 372

Web Field/UCI/Package Option

Description

Web: ESSID
UCI: wireless. @wifi-iface[0]..ssid
Opt: ssid

Extended Service Set Identification. Type the name of the

wireless local area network.

Web: Mode
UCI: wireless.@wifi-iface[0].mode
Opt: mode

Mode type. For AP mode, select Access Point.

Web value

UCI

Access Point

Client

sta

Ad-Hoc

adhoc

802.11s

mesh

Pseudo Ad-Hoc (ah

demo)

ahdemo

Monitor

monitor

Access Point (WDS)

ap-wds

Client (WDS)

sta-wds

Web: Mode
UCI: wireless.@wifi-iface[0].bssid
Opt: bssid

Defines the BSSID value. Only displayed if using client, ad-hoc or

client (wds) modes.

Web: Network
UCI:wireless.@wifi-iface[0].network
Opt: network

The network the wireless interface is attached to. If using an

existing interface select the appropriate network. Select

unspecified to not attach to any network or fill out the create

field to define a new network.

Web: Hide ESSID
UCI: wireless.@wifi-iface[0].hidden
Opt: hidden

Hides the SSID when enabled. Only displayed if using access

point or access point (wds) modes

Enabled.

Disabled.

Table 59: Information table for the interface configuration general setup section

22.2.2.2

Interface configuration: wireless security

Use this section to configure encryption, ciper and create a security key. Differing
options wil be defined depending on the encryption selected.

Figure 91: The wireless security section

Содержание GW3330





















































































































































































































































































































































































Результаты поиска

Содержание GW3330

Отзывы:

Похожие инструкции для GW3330

Бренды по названию

Популярные бренды

virtual access GW3330, Руководство пользователя

Результаты поиска

Содержание GW3330

Отзывы:

Похожие инструкции для GW3330

Бренды по названию

Популярные бренды