virtual access GW3330 Скачать руководство пользователя страница 120

Страница: 120 / 372

15: Configuring SAToP and CESoPSN

_______________________________________________________________________________________________________

_____________________________________________________________________________________________________

GW3300 Series User Manual

Issue: 1.7

Page 120 of 372

Figure 67: CESoPSN ALL port settings

Web Field/UCI/Package Option

Description

Web: Enable
UCI: cesopd.[port].enable
Opt: enable

Enables the port.

Disabled.

Enabled.

Web: Local IP
UCI: cesopd.[port].udp_local_ipaddr
Opt: udp_local_ipaddr

Specifies the interface IP address to listen on for incoming

packets.

127.0.0.1

Specific interface IP address.

0.0.0.0

Listens on all available interfaces.

Web: Local Port
UCI: cesopd.[port].udp_local_port
Opt: udp_local_port

UDP port to listen for incoming packets on.

5566

49152-65535 recommended.

Range

0-65535

Web: Remote IP
UCI: cesopd.[port].udp_remote_ipaddr
Opt: udp_remote_ipaddr

Specifies the remote IP address to send packets to.

127.0.0.1

Specific remote interface IP address.

Range

Packets are accepted from all sources and

received source IP address will be used as

the destination.

Web: Remote Port
UCI: cesopd.[port].udp_remote_port
Opt: udp_remote_port

UDP port to send packets to. The port can be 0; in which case

the source port of the incoming packets will be used as the

destination.

6655

49152-65535 recommended.

Range

0-65535

Web: Packetization Latency
UCI: cesopd.[port].packetization_latency
Opt: packetization_latency

Specifies the packetization latency.

Range

5-20 milliseconds.

Web: Clock Recovery
UCI:

cesopd.[port].clock_recovery_enabled
Opt: clock_recovery_enabled

Enables the port to use the received packet data to adjust the

TDM data clock of the router.
Note: enable clock recovery on one port only.

Disabled.

Enabled.

Web: Enable RTP Header
UCI: cesopd.[port].rtp_header_enabled
Opt: rtp_header_enabled

Enables the use of RTP header as specified in RFC5086.
Note: before disabling the use of RTP header, ensure that the

peer supports this.

Disabled.

Enabled.

Содержание GW3330





















































































































































































































































































































































































Результаты поиска

Содержание GW3330

Отзывы:

Похожие инструкции для GW3330

Бренды по названию

Популярные бренды

virtual access GW3330, Руководство пользователя

Результаты поиска

Содержание GW3330

Отзывы:

Похожие инструкции для GW3330

Бренды по названию

Популярные бренды