INSTRUCTION FOR USE
ENGLISH
23
SQUEEGEE BLADE CHECK AND REPLACEMENT
1.
Clean the steel or the plastic squeegee, as shown in the
previous paragraph.
2.
Check that the edges (E, Figure 16) of the front blade (A)
and the edges (F) of the rear blade (C) lay down on the same
level, along their length; if necessary adjust their height
according to the following procedure:
Loosen the all wing nuts (J) and adjust the front blade (A)
and rear blade (C), then tighten the all wing nuts.
3.
Check the front blade (A) and rear blade C) for wear, cuts
and tears; if necessary replace them according to the
following procedure. Check that the front corner (E) or the
rear corner (F) is not worn; if necessary, overturn the blade
to replace the worn corner with an integral one. If the other
corners are worn too, replace the blade according to the
following procedure:
Remove the all wing nuts (J) and the screw (K), remove the
retaining strip (B), then replace/overturn the front blade
(A). Assemble the blade in the reverse order of disassembly.
Remove the all wing nuts (J) and the screw (K), remove the
retaining strip (D), then replace/overturn the rear blade (C).
Assemble the blade in the reverse order of disassembly.
After the blade replacement (or overturning), assemble the
squeegee as shown in the previous step.
4.
Install the squeegee (E, Figure15) and screw down the
knobs (D, Figure15).
5.
Connect the vacuum hose (B, Figure15) to the squeegee (C,
Figure15)
G
A
C
I
H
F
E
B
A
C
D
K
J
Figure 16
TANK AND VACUUM GRID WITH FLOAT CLEANING, AND COVER GASKET CHECK
1.
Push the machine to a level floor.
3.
Ensure that the machine is off.
4.
Turn the recovery tank lid (A, Figure17) 90 degrees position where it can be taken off from the recovery
tank, and then take out the float ball filter (B) from the recovery tank lid.
5.
Clean the recovery tank lid (A), recovery tank (C), clean solution tank(D) and the float ball filter(B). Empty
the recovery tank with the drain hose (D, Figure 11).
6.
Install the float ball filter(B)and the recovery tank lid(A).
7.
Inspect the integrity of the tank sealing strip.
NOTE
The tank sealing strip (E) produces the vacuum inside the tank when the vacuum motor
works. The tank must be sealed so it can effectively absorb the water from the ground to
recovery tank.
Содержание AS4325B
