VIPA SLIO IM 053-1DN00 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 44

VIPA SLIO IM 053-1DN00 Скачать руководство пользователя страница 23

Manual VIPA System SLIO

Chapter 1 Basics and Assembly

HB300E - IM - RE_053-1DN00 - Rev. 11/21

1-15

Trouble shooting - LEDs

Each module has the LEDs RUN and MF on its front side. Errors or
incorrect modules may be located by means of these LEDs.
In the following illustrations flashing LEDs are marked by

☼

.

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

Behavior:

After PowerON the RUN LED of each module is off and the MF

LED of each module is sporadically on.

Reason:

The maximum current for the electronic power supply is

exceeded.

Remedy:

As soon as the sum current of the electronic power supply is

exceeded, always place the power module 007-1AB10.
More concerning this may be found above at "Wiring".

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

Behavior:

After PowerON the MF LED of one module respectively more

modules flashes. The RUN LED remains off.

Reason:

At this position a module is placed, which does not correspond to

the configured module.

Remedy:

Match configuration and hardware structure.

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

RUN
MF

Behavior:

After PowerON all of the RUN LEDs up to the defective module

are flashing. With all following modules the MF LED is on and the RUN
LED is off.

Reason:

The module on the right of the flashing modules is defective.

Remedy:

Replace the defective module.

General

Sum current of the
electronic power
supply exceeded

Error in
configuration

Module failure

«
...
21
22
23
24
25
...
»

Содержание SLIO IM 053-1DN00













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды