Vintage Air 565701 Скачать руководство пользователя

Страница: 26 / 34

www.vintageair.com

905701 REV B 09/18/18, PG 26 OF 34

Driver and Passenger Side

Louver Installation (Cont.)

Install the louver bezel brackets between the louver housings and the hose adapters (See Photo 7, below).

Install the louver through the louver housing and into the hose adapter, and then tighten to secure the

assembly together (See Photos 8, 9 & 10, below).
Install the driver side louver assembly onto the previously drilled hole on the bottom of the dash, and secure

it using a 10-24 nut with star washer (See Photo 11, below). NOTE: The driver side louver housing has

a notch for easy installation next to the parking brake. This louver will use the louver mounting

bracket with a smaller slot.
Install the passenger side louver assembly onto the previously drilled hole on the bottom of the dash, and

secure it using a 10-24 nut with star washer (See Photo 12, below).

Photo 7

Photo 8

Photo 9

Photo 10

Photo 11

Photo 12

Hose

Adapter

Hose

Adapter

Louver Bezel

Bracket

Louver

Housing

Passenger Side

Louver

Driver Side

Louver

Содержание 565701



































Результаты поиска

Содержание 565701

Отзывы:

Похожие инструкции для 565701

Бренды по названию

Популярные бренды

Vintage Air 565701, Руководство пользователя

Результаты поиска

Содержание 565701

Отзывы:

Похожие инструкции для 565701

Бренды по названию

Популярные бренды