background image

                                                       

 

                       

 

- 18 - 

                                        

 

         

  Fig. 7 WM-Liquid Filter          Fig. 8 WM-Liquid Indicator         

   

2.  Temperature Controller and Air Probe Location 
 

1)  The temperature controller can be mounted either inside or outside the wine 

cellar,  but  the  air  probe  must  be  located  inside  the  wine  cellar  or  the  return 
duct. 

2)  The air probe shall be located in the wine cellar 5 ft above the floor or the air 

return  area,  but  it  shall  not  be  located  in  the  air  supply  area  or  other  areas 
where air is not circulated. 

3)  Air  probe  can  be  pulled  out  of  the  temperature  controller  up  to  5  ft.  If 

additional wires are necessary, 18 gauge wires may be used to extend the air 
probe. 

 

3.  Evaporator Unit Location 

 

1)  The  WM-25~65SFCV  evaporator  units  should  be  installed  for  corner  mount 

with the supply air on the top and return air on the bottom. 

2)  Air  supply  shall  be  unobstructed  minimum  12”;  air  return  shall  be 

unobstructed minimum 6”. 

3)  A grille can be used to cover the supply and return with 0~2” clearance; or a 

2-3 ft long duct can be added at the supply and return. 

4)  There is a gravity drain system, so the unit shall be installed level or with a 

slight  slope  downward  the  drain  connection  and  the  drain  line  shall  be 
installed slope down toward the drain.  
If rise-up is necessary, a condensation pump must be used. 
 

4.  Condensing Unit Location 

 

 

 
 

CAUTION 

Low  ambient  condition  kit  is  required  if  the  temperature  will  be 
below 50

°

F.

 

Содержание WINE-MATE WM-2500SSV
































Отзывы: