EN
Transponder reader for access control,
white LED backlighting, 1 input that can
be enabled for an additional button, 1 NO
relay output, to be completed with front
panel.
1. Description
The device allows access control and actuator control by
RFID card. Four possible operating modes, according to
type of installation:
standalone
,
slave-2wire, eipvdes
(IP Video-Door Entry System)
,
o
r
slave-eipvdes
. For the
standalone
and
slave-2wire
operating modes, the con-
figuration management and update software to be used is
SaveProg; for
eipvdes
and
slave-eipvdes
, Video Door
IP Manager
is to be used.
In
standalone
mode (factory default setting), recognition
of a previously registered card commands activation of
output F1. It is also possible to enable input CA for the
connection of an additional pushbutton and directly com-
mand output F1. In this mode, SaveProg can be used to
register cards and configure the device.
In
slave-2wire
mode, the device must be connected to
an electronic audio or audio/video module in the Pixel
2-wire series using specific wiring (connectors
f
or
g
). The
above description for
standalone
mode applies. Alterna-
tively, output F1 may be used to control any other output
(relay/lock) of the audio or audio/video module or other
auxiliary modules of the external unit.
In
eipvdes
mode, the device must be connected directly
(via RJ45 interface) to a network on which an Elvox IP
video door entry service is provided. Device program-
ming and configuration operations are performed using
Video-Door IP manager. Each registered card, and also
input CA, can be associated with activation of an actua-
tor in the video door entry system (including the local F1
relay). Alternatively, CA can be configured as the sensor
input for the "door open" signal.
In
slave-eipvdes
mode, the device must be connected
to an electronic audio or audio/video module in the Pixel
IP series using specific wiring (connectors
f
or
g
). The
functional characteristics, the programming and the con-
figuration operations are the same as described for the
eipvdes
mode.
In the factory default setting (
standalone
mode), the de-
vice, if connected to an Elvox IP video door entry system,
can be identified and configured using Video-Door IP
Manager. Once the first configuration has been complet
-
ed, the operating mode will be set as
eipvdes
.
However,
for the
slave-2wire
and
slave-eipvdes
operating modes,
slave mode must be specifically set using SaveProg.
Any of the supported operating modes may be set using
SaveProg at any time.
The device is compliant with the ISO 14443A/MIFARE
standard: MIFARE™ CLASSIC (1K e 4K), MIFARE UL
-
TRALIGHT™ (ULTRALIGHT EV1/ULTRALIGHT C) and
MIFARE DESFire™ (DESFIRE EV1 2K/4K/8K).
2. Characteristics
• Power supply:
1) from the electronic audio or audio/video module,
via specific wiring
(
slave-2wire
and
slave-eipvdes
modes
);
2) from additional power supply unit on terminals 5V+
and 5V- (all operating modes);
3) Power-over-Ethernet Class 0 (IEEE 802.3-2012) via
RJ45 interface. NOTE: The RJ45 network interface
is to be connected exclusively to a SELV (Safety
Extra-Low Voltage) network. The Power-over-Eth-
ernet power supply unit (PSE) must provide elec-
trical insulation between any accessible conductor
including the earth wire, if there is one, and all the
contacts of the network ports, including those not
used by the PSE or by the device to be installed
(
eipvdes
mode).
• Maximum power consumption: 250 mA at 5V.
•
Average PoE consumption: 2.5 W.
• Operating temperature range: -25 °C / +55 °C.
• Ingress protection rating: IP54.
• Protection rating against impact: IK08.
• Frequency range: 13,553-13,567 MHz
• RF transmission power: < 60 dBμA/m
• Operating distance: up to 1 cm.
•
Compatible with Vimar programmable transponder
card (art. 01598).
3.
Standalone
and
slave-2wire
modes
A maximum of 2000
user
or
installer
cards can be reg-
istered in total. The first type can be used to activate the
configured actuator, while the second can be used to
register new user card without having to use SaveProg
(manual registration).
By default, only the use of MIFARE CLASSIC 1K cards is
enabled. Using SaveProg, it is possible to enable the use
of other types of card.
3.1 Configuration
Connect the device to the PC using a USB cable. Refer
to the SaveProg documentation for specific details. It is
possible to:
•
Set the operating mode:
standalone
,
slave-2wire,
slave-eipvdes
or
eipvdes
.
•
Add and remove user and installer cards.
•
Associate each card with a name and an extension
number in order to simplify removal. The cards are
saved on the device with a unique, sequential rec-
8
41017
