background image

VK1001 STANDARD 

RESPONSE UPRIGHT 

SPRINKLER (K5.6)

TECHNICAL DATA

The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058

Telephone: 269-945-9501  Technical Services: 877-384-5464  Fax: 269-818-1680  Email: [email protected]

Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com

Page 4 of 4

Form No. F_102420    Rev 22.1    February 22, 2022

Figure 3: Installation

Frame arms must be 

parallel to the pipe.

1

2

1. Carefully slide the wrench onto the 

wrench flats. 

2. Install the sprinkler into the pipe fitting. 

NOTE: 

The sprinkler frame arms shall be 

parallel to the pipe.

DESIGN CRITERIA - UL

cULus Listing Requirements:

The Viking VK1001 Standard Response Upright Sprinkler is cULus Listed as indicated in Approval Chart for installation in 

accordance with the latest edition of NFPA 13 for standard spray sprinklers.

•  Designed for use in Light, Ordinary, and Extra Hazard occupancies.

•  The sprinkler installation rules contained in NFPA 13 for standard spray upright sprinklers shall be followed.

DESIGN CRITERIA - FM

FM Approval Requirements:

The Viking VK1001 Standard Response Upright Sprinkler is FM Approved as standard response Non-Storage upright sprinkler as 

indicated in the FM Approval Guide. For specific application and installation requirements, reference the latest applicable FM Loss 

Prevention Data Sheets (including Data Sheet 2-0). FM Global Loss Prevention Data Sheets contain guidelines relating to, but not 

limited to: minimum water supply requirements, hydraulic design, ceiling slope and obstructions, minimum and maximum allowable 

spacing, and deflector distance below the ceiling.

NOTE: 

The FM Installation guidelines may differ from UL and/or NFPA criteria.

IMPORTANT: Always refer to Form Number F_091699 - Care and Handling of Sprinklers. Also refer to Form Number 

F_080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance 

with the latest edition of Viking Technical Data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or 

other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever 

applicable.

Replaces page F_102420 Rev 21.2

(Added LPCB and VdS details)

Содержание VK1001


















Отзывы: