Viking VK1001 Скачать руководство пользователя страница 17

Страница: 17 / 17

XT1 Sprinkler and

XG Guard Assemblies

BULLETIN

The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058

Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: [email protected]

Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com

Page 1 of 1

Form No. F_091119 19.09.11 Rev 19.1

1. INTRODUCTION

The purpose of this bulletin is to inform users of proper XG Guard usage for the Model XT1 Sprinklers. The XG Guard assemblies

are specifically listed and approved for use on Model XT1 Sprinklers; no other guard assemblies should be used.

WARNING

Viking sprinklers are manufactured and tested to meet the rigid requirements of the approving agency. The sprinklers

are designed to be installed in accordance with recognized installation standards. Deviation from the standards or

any alteration to the sprinkler after it leaves the factory including, but not limited to: unlisted accessories, painting,

plating, coating, or modification, may render the sprinkler inoperative and will automatically nullify the approval and any

guarantee made by The Viking Corporation. Refer to the Authority Having Jurisdiction prior to installation.

2. GENERAL INFORMATION:

A potential product performance issue may exist when listed products are combined with unlisted product(s) that have not been

evaluated together by a recognized approval laboratory. With the development of new products and existing products, it is extremely

important to correctly match a sprinkler with a sprinkler guard. Please refer to the appropriate manufacturer’s technical literature or

call Viking Technical Services at 877-384-5464.

IMPORTANT

Model XT1 sprinklers are specifically listed and approved with XG Guard. The XG Guard, part number 22931, is listed

and approved for use with the following XT1 sprinklers: VK1001, VK1021, VK3001, VK3021, VK2002, VK2022, VK3502,

VK3522, VK2001, VK2021, VK3501, VK3521.

Listed and Approved XG Guard/XT1 Sprinkler Assembly

Unlisted Guard/XT1 Sprinkler Assembly

NOTE: Image is represetative only. Actual product appearance may vary.

Activation

element T-hinge

blocked

Содержание VK1001


















Результаты поиска

Содержание VK1001

Отзывы:

Похожие инструкции для VK1001

Бренды по названию

Популярные бренды

Viking VK1001, Технические данные инструкция

Результаты поиска

Содержание VK1001

Отзывы:

Похожие инструкции для VK1001

Бренды по названию

Популярные бренды