Connect a 4-wire modular cord from the
RAD-AMP
Line Out jack to the
625A jack. Test the contact closure operation by calling into the
RAD-
AMP
and verifying proper operation.
Note:
The
RAD-AMP
is factory
configured with this feature disabled. To
activate this feature see section
F
in
Programming
. The Red-Green pair is the
outgoing line of the
RAD-AMP
, while the
Yellow-Black pair provides the auxiliary
contact closure.
C. Installing the Auxiliary Contact Closure
LINE OUT
USE ONLY LISTED
CLASS 2 POWER
SOURCE 12V DC
500mA MAXIMUM
LINE IN
REMOTE
SWITCH
Black
Yellow
Red
Green
4-Wire Modular
Cable
To device
requiring
contact closure
600 Ohms
Output of RAD-AMP
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
A. Line Extender Mode
To access programming in the “Line Extender” mode, call into the
LINE IN
port. After the
RAD-AMP
answers, enter a
✱
followed by
the security code, factory set to V-I-K-I-N-G (
845464
). The
RAD-AMP
will beep twice indicating that programming has been
accessed. It is recommended that the factory security code be changed. While programming, if 20 seconds elapse between Touch
Tones, the
RAD-AMP
will disconnect. All valid Touch Tone programming sequences are acknowledged with a double beep. A triple
beep indicates that a mistake has been made.
Note:
If a “Priority 2” access code is used, program the “PABX outside line num-
ber” with the Touch Tone required to access a C.O. line from a PABX extension.
Line Extender Quick Programming Features
Set the
RAD-AMP
to Line Extender mode (factory set) ...........................................
Set the
RAD-AMP
to Call Diverter mode (see section
B
) ........................................
Set the
RAD-AMP
to Telecommuting Extender mode (see section
C
) .....................
Security code (6 digits 0-9) (factory set to 845464) ..................................................
“Priority 1” access code (enter 6 digits, no digits disables) (factory disabled) ..........
“Priority 2” access code (enter 6 digits, no digits disables) (factory disabled) ..........
PABX outside line number (enter 1 digit, no digit disables) (factory set to 9) ............
SO-24A mode enabled (see
Operation
section
D
) ..................................................
SO-24A mode disabled (factory setting, see
Operation
section
D
) .........................
Maximum call timer (enter 2 digits*, no digits disables - factory disabled) .................
Ring delay (1-9) (factory set to 1) .............................................................................
Alert tones On (call progress beeps) (factory enabled) ............................................
Alert tones Off ..........................................................................................................
Enable dial tone detection (for installations without CPC or busy signal) .................
Disable dial tone detection (factory setting) .............................................................
Exit programming and disconnect ...........................................................................
Set all programming features to factory settings ......................................................
* Note:
Call timer digits specified as follows: 00 = 15 seconds, 01-99 = .5 - 49.5 minutes in .5 minute increments.
✱
1
✱
2
✱
3
6 digits
6 digits
6 digits
1 digit
✱ ✱
✱
#
2 digits
1 digit
✱
9
✱
0
✱
5
✱
6
# 7
###
# 47
# 45
# 46
# 44
# 48
# 49
Enter Digits
then
then
then
then
then
then
- then - Enter Memory Location
B. Call Diverter Mode
To access programming in the “Call Diverter” mode, call into the
LINE IN
port. After the called party answers, enter a
✱
followed by
the security code, factory set to V-I-K-I-N-G (
845464
). The
RAD-AMP
will beep twice indicating that programming has been
accessed. It is recommended that the factory security code be changed. While programming, if 20 seconds elapses between Touch
Tones, the
RAD-AMP
will disconnect. All valid Touch Tone programming sequences are acknowledged with a double beep. A triple
beep indicates that a mistake has been made.
Call Diverter Quick Programming Features
Set the
RAD-AMP
to Line Extender mode (see section
A
) .......................................
Set the
RAD-AMP
to Call Diverter mode .................................................................
Set the
RAD-AMP
to Telecommuting Extender mode (see section
C
) .....................
Security code (6 digits 0-9) (factory set to 845464) ..................................................
Call Diverter number (1-32 digits) ............................................................................
To enter a “
✱
” in the Call Diverter number ................................................................
To enter a “#” in the Call Diverter number ................................................................
To enter a 1 second pause in the Call Diverter number ............................................
Maximum call timer (enter 2 digits*, no digits disables - factory disabled) .................
Ring delay (1-9) (factory set to 1) .............................................................................
Enable dial tone detection (for installations without CPC or busy signal) .................
Disable dial tone detection (factory setting) .............................................................
Exit programming and disconnect ...........................................................................
Set all programming features to factory settings ......................................................
* Note:
Call timer digits specified as follows: 00 = 15 seconds, 01-99 = .5 - 49.5 minutes in .5 minute increments.
✱
1
✱
2
✱
3
6 digits
1-32 digits
✱ ✱
✱
#
✱
8
2 digits
1 digit
✱
5
✱
6
# 7
###
#47
# 00
# 48
# 49
Enter Digits
then
then
then
then
- then - Enter Memory Location
Rear View of
the RAD-AMP
3
