Viking PSA-IP Скачать руководство пользователя | Manualshive

Страница: 20 / 24

background image

20

C. Operation Commands (Relay Mode must be set to “Door Strike”)

Feature

Tone Tone
Command

Description

Activate

Ext Relay

QQ

or

___ ___

Momentarily activate ext relay (1 or 2 digits, factory set to

QQ

).

Un-Latch

Ext Relay

Q

0

Un-latch* (deactivate) the ext relay.

Latch

Ext Relay

Q

1

Latch* (continuously activate) the ext relay.

Disconnect

#

Disconnects or forces the speaker to hang up.

* NOTE:

Latching commands must be enabled in programming.

The following commands can be entered after the

PSA-IP

answers an inbound SIP call, when the Inbound Call Mode

is set to auto answer. After the unit auto answers the call, one beep will be heard if Pre Page Alert Tone is enabled. If
the Access Code has been disabled, you can now enter the Operation Commands listed below. If an Access Code has
been programmed, enter the Access Code digits. Once the correct code has been entered, two beeps will be heard
and you can now enter the Operation Commands listed below.

Troubleshooting

If the unit cannot register with the programmed SIP server, the “Status” LED will blink on and off every two seconds until
communication is restored. This alerts a potential user of a problem with the device that will prevent SIP calls from being
accepted.

«
...
18
19
20
21
22
...
»

Содержание PSA-IP

























Отзывы:

Нет отзывов

Похожие инструкции для PSA-IP

Бренд: IFM Electronic Страницы: 6

TL-PA201 STARTER

Бренд: TP-Link Страницы: 2

Versa WiFi USB Adapter 3

Бренд: C. Crane Страницы: 30

Бренд: NI Страницы: 11

Бренд: Microsemi Страницы: 17

Бренд: Netronix Страницы: 87

Бренд: Rosewill Страницы: 29

Xcomfort CSAP-01/0 Series

Бренд: Moeller Страницы: 4

Бренд: Akitio Страницы: 8

AirLancer Extender SA-5L

Бренд: Lancom Страницы: 2

Бренд: Kvaser Страницы: 21

Бренд: MSG Equipment Страницы: 12

Бренд: Dynex Страницы: 11

Stylus COLOR 3000

Бренд: Epson Страницы: 1

Бренд: HP Страницы: 86

Бренд: HP Страницы: 12

Бренд: HP Страницы: 20

Бренд: HP Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды