7
G. Assisted Programming
When attempting to program the
E-30/32
phone, if the phone number of the line it is connected to is not known, the phone can be
set to automatically call Viking technical support for assistance. With DIP switch 3 set to OFF (programming mode), pushing the
CALL button will cause the
E-30/32
phone to call Viking, whether it be connected directly to a CO line, or behind a "dial 9" PBX.
The
E-30/32
phone will first dial 9, and then listen for second dial tone; if detected it will continue to dial Viking’s assisted programming
phone number. If a second dial tone is not detected, it then knows it is not behind a PBX, so it will momentarily hang up and then
directly dial Viking’s assisted programming phone number. Since this is a long distance phone call, the line must be capable of placing
long distance calls for the call to go through. When finished programming, it is very important to set DIP switch 3 back to ON (normal
operating mode), and place a test emergency call to be sure all programming was done properly.
Warning: Failure to set DIP switch 3 back to ON when finished programming will cause the E-30/32 phone to
call Viking Technical Support, instead of your programmed speed dial number. Yet, as a fail-safe measure, after
3 calls to Viking, the unit will ignore switch 3 and dial its programmed phone numbers.
Speaker
Volume
ON
OFF
ON
OFF
1 2 3
A
B
Standard
OFF ON
EWP
A B
Standard
OFF ON
1
2
3
EWP
H. DIP Switch Programming/Speaker and Microphone Adjustments
A speaker volume POT is provided to increase or decrease the speakerphone volume.
Note:
The Microphone Sensitivity POT has been
removed because the microphone sensitivity is now microprocessor controlled. This allows the mic gain to be automatically increased
in a quiet environment, allowing the distant party to clearly hear even soft or distant sounds. The microprocessor will automatically reduce
the mic sensitivity when the location becomes noisy. This Automatic Noise Canceling (ANC) feature will allow speakerphone two-way
communications to continue to work properly, even when subjected to loud noise such as a diesel engine or traffic.
Switch A
Switch B Description
ON
ON
Normal audio detection
OFF
OFF
Increase audio detect sensitivity for low level lines. Useful in applications in
which voice or busy signals have trouble breaking over the speaker.
Switch
Position
Description
1
ON
“CALL” button alternately connects/disconnects calls (factory default)
1
OFF
“CALL” button connects calls only
2
ON
Incoming calls answered (factory setting)
2
OFF
Incoming calls are not answered
3
ON
Normal operation mode (factory setting)
3
OFF
Learn mode - Any incoming calls are automatically entered into the
programming mode (no security code required). Use this option if you have
forgotten your security code. Any outbound call will dial Viking Technical
Support (see section
I
).
Warning: When finished programming, set this switch
back to the ON position, otherwise the E-30/32 phone will only call Viking
Technical Support instead of your programmed emergency number.
I. Programming Examples
To Program the E-30/32 Phone...
Step 1
Step 2
...to store 123456 as the security code
Access Programming (see page 3)
Enter digits:
1 2 3 4 5 6 # 1 9
...to store 555-1234 in the second speed dial position
Access Programming (see page 3)
Enter digits:
5 5 5 1 2 3 4 # 0 1
...to store a touch tone 9, a four second pause, and then a
pulse dialed 333-4444 into the first speed dial position
Access Programming (see page 3)
Enter digits:
9
Q
7
Q
6 3 3 3 4 4 4 4 # 0 0
Operation
When the “
Call
” button is pressed, the
E-30/32
phone goes off-hook, and dials a pre-programmed telephone number. The
front panel LED will light any time the phone is off hook, and flash to show dialing. In the event that the line is busy or there
is a ring-no answer, the unit can be programmed to call additional phone numbers. The phone then cycles through up to 5
pre-programmed speed dial numbers until the call is answered. The
E-30/32
will hang up on CPC, silence, busy signal,
return to dial tone, time out or Touch Tone command (
Q
#
). If programmed to auto-answer, the
E-30/32
will also answer any
incoming call.
