Viking DGVU2004B-30, Руководство по обслуживанию

Страница: 10 / 29

10
© 2011 Viking Preferred Service © 2011 Viking Preferred Service
10
General Information
Gas Requirements (continued)
Pressure regulator:
UÊÊ ÊÊ/ iÊÀi}Տ>̜ÀÊÃÕ««ˆi`ÊÜˆÌ ÊÌ iÊ61Ê
cooktops must be installed before any gas
connections are made. It is preset for use with
natural gas. This must be converted to use with
LP/Propane gas.
UÊ Ê>˜ˆvœ`Ê«ÀiÃÃÕÀiÊà œÕ`ÊLiÊV iVŽi`ÊÜˆÌ Ê>Ê
manometer. Natural gas requires 5.0” WCP and
LP/Propane requires 10.0” WCP. Incoming line
pressure upstream for the regulator must be 1”
WCP higher than the manifold pressure in order
to check the regulator.
UÊÊ Ê/ iÊÀi}Տ>̜ÀÊÕÃi`ʜ˜ÊÌ ˆÃÊVœœŽÌœ«ÊV>˜Ê
withstand a maximum input pressure of 1/2 PSI
(14.0” WCP). If the line pressure is in excess
of that amount, a step-down regulator will be
required.
UÊ Ê/ iʓ>˜Õ>Êà ÕÌʜvvÊÛ>ÛiÊ>˜`Ê«ÀiÃÃÕÀiÊ
regulator on these cooktops must be
disconnected from the gas supply piping
system during any pressure testing of that
system at pressures in excess of 1/2 PSI
(3.45kPa.)
UÊÊ Ê/ iÊVœœŽÌœ«Ê“ÕÃÌÊLiʈ܏>Ìi`ÊvÀœ“ÊÌ iÊ}>ÃÊ
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at
test pressures equal to or less than 1/2 PSI
(3.45kPa).
IMPORTANT: NEVER refuse old connectors
when installing this cooktop.
Rigid Connections:
UÊÊ Ê˜Vœ“ˆ˜}Ê}>ÃʈÃÊLÀœÕ} ÌÊvÀœ“Ê>˜Êˆ˜Ì>ŽiÊ«ˆ«iÊ>ÌÊ
the rear of the unit to the pressure regulator;
then to the manifold pipe for distribution. The
intake pipe and shut-off valve are not supplied.
The intake pipe and the shut-off valve should
be connected to the regulator to complete the
connection.
In Massachusetts: This appliance must be
installed with a 36” (3-foot) long flexible gas line.
UÊ Ê/ iÊ>ˆ}˜“i˜ÌʜvÊÌ iÊÛ>ÛiÃÊà œÕ`ÊLiÊV iVŽi`Ê
after connecting the cootkop to the gas supply
to be sure the manifold pipe has not been
moved. A misalignment may cause the valve
knob stem to rub on the control panel, resulting
in a gas leak at the valve.
UÊÊ Ê˜ÃÌ>iÀ‡ÃÕ««ˆi`ʈ˜Ì>ŽiÊ«ˆ«iÃÊà œÕ`ÊLiÊ
checked visually for any foreign matter before
installing in a service line.
Proper Lighting and Shutdown Instructions
To ignite electric igniters on the surface burners:
1. Turn the knob counterclockwise to any
position.
2. Upon ignition of the surface burner, turn the
knob to the desired position (HI, Med or Low).
3. To shutdown the burner, turn knob clockwise to
the OFF position.
In case of failure, shut the gas OFF using the
installer supplied manual shut-off valve.