Viking Built-in French Door Bottom-Freezer Refrigerator, Руководство по установке

Страница: 3 / 12

5 4
T To oo ollss N Ne ee ed de ed d
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here
• Cordless drill • Torx® T15 and T27 screwdrivers
• Drill bits • ¹¹⁄ 32 " nut driver
• Adjustable wrenches (2) • ³⁄ 8 ", ¹⁄ 4 ", and ¹⁄ 2 " open-end wrenches
• Phillips screwdriver • 5 ⁄ 32 " hex key
• Small level • ¹⁄ 4 " and 5 ⁄ 16 " socket drivers
• Appliance dolly • Tape measure
• Utility knife
P Pa arrttss N Ne ee ed de ed d
• Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)
• One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)
• If you are connecting the water line directly to copper tubing and not to a shutoff valve, you
need a ferrule, a union, and a ¹⁄
4
" compression fitting.
IIM MP PO OR RT TA AN NT T::
• Observe all governing codes and ordinances.
• It is recommended that you do not install the refrigerator near an oven, radiator, or other
heat source.
• Installer: Leave Installation Instructions with the homeowner.
• Homeowner: Keep Installation Instructions for future reference. Save these Installation
Instructions for the local electrical inspector’s use.
• Do not install in a location where the temperature will fall below 55°F (13°C).
• Floor must support the refrigerator weight, more than 600 lbs (272 kg), door panels and
contents of the refrigerator. Floors underneath refrigerator are level with surrounding finished
floor.
• Cutout dimensions are accurate.
• Ceiling height must allow for side tipping radius.
• Location should permit door to open fully.
• Location must permit top grille removal.
Electrical Requirements IMPORTANT–
Please Read and Follow!
Before you move your refrigerator into its
final location, it is important to make sure
you have the proper electrical and water
supply connections installed..
R Re ecco om mm me en nd de ed d G Grro ou un nd diin ng g M Me etth ho od d
A grounded 3-prong electrical outlet should
be placed within 10” (25.4cm) of the right
side cabinets or end panel with a 115 volt,
60 Hz., AC only, 15- or 20-amp fused,
grounded electrical supply. It is
ecommended that a separate circuit serving
only your refrigerator be provided. Use an
outlet that cannot be turned off by a switch.
Do not use an extension cord.
It is the customer’s responsibility to:
• Contact a qualified electrical installer.
• Assure that the electrical installation is
adequate and in conformance with the
National Electrical Code, ANSI/NFPA 70-
latest edition or Canadian Electrical Code
C22.1-1998 and C22.2 No. 0-M91 (or
latest edition), and all local codes and
ordinances. A 115 volt, 60-Hz, 15 amp,
fused, electrical supply is required.
If codes permit a separate grounding wire to
be used, it is recommended that a qualified
electrician determine that the grounding
path is adequate.
D DO O N NO OT T ground to a gas pipe. Check with a
qualified electrician if you are not sure the
appliance is properly grounded. D
DO O N NO OT T
have a fuse in the neutral or grounding
circuit.
IIM MP PO OR RT TA AN NT T: If this product is connected to
a GFCI (Ground Fault Circuit Interrupter)
protected outlet, nuisance tripping of the
power supply may occur, resulting in loss of
cooling. Food quality and flavor may be
affected. If nuisance tripping has occurred,
and if the condition of the food appears
poor, dispose of it.
N NO OT TE E: Before performing any type of
installation, cleaning, or removing a light
bulb, remove the top grille and turn the
master power switch to OFF or disconnect
power at the circuit breaker box.
When you are finished, turn ON the master
power switch or reconnect power at the
circuit breaker box. Then reset the control to
the desired setting.
W A R N I N G
ELECTRICAL SHOCK
HAZARD
• Plug into a grounded 3-
prong plug.
• Do not remove grounding
plug.
• Do not use an adapter.
• Do not use an extension cord.
Failure to followthese instructions can
result in death, fire, or electrical shock.
Most of the unit’s weight is at the top. Extra care is needed when moving the unit to
prevent tipping. Use cardboard shipping material or plywood under unit until it is
installed in the operating position to protect floor surface.