VIGO VG151017, Руководство пользователя

Страница: 28 / 46

3
Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals as these will scratch, dull, and/or
damage the finish and void the warranty.
MAINTENANCE
ASSEMBLY
REQUIRED TOOLS
Adjustable wrench
Allen key - supplied (to remove cartridge if needed)
Plumber's putty - optional
Plumber's tape
Flat screwdrivers
SAFETY TIPS
If you use soldering for the installation of the faucet, the seats, cartridges and
washers will have to be removed before using flame. Damage caused by
improper soldering will void the warranty.
Protect your eyes with safety glasses when cutting or soldering water supply
lines.
IMPORTANT POINTS
Prior to beginning installation, turn off the cold and hot water lines and open the
hot and cold knobs on the old faucet to release pressure.
When installing your new faucet, turn the connector nuts finger-tight, then use
one wrench to anchor the fitting and a second wrench to tighten the nut.
Connections that are too tight will reduce the integrity of the system and
potentially cause product failure which could lead to water damage.
Wrap all threaded connections with plumber's tape available at your local
hardware or plumbing supply store. Always wrap in a clockwise direction.
Not all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.
Prior to installing the faucet please FLUSH THE HOT AND COLD WATER
SUPPLY LINES that are or will be connected to the new faucet to remove scale,
solder or their impurities which could damage the faucet and potentially void the
warranty.
INSTALLATION
Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
3
PLASTIC HOLDER
ALLEN KEY (REMOVES HANDLE
TO ACCESS CARTRIDGE)
TWO METAL
BRAIDED HOSES
PLATE
SPRAYER
METAL RING
RUBBER RING
6
2
1
FAUCET
ASSEMBLY
PACKAGE CONTENTS
1. SHUT OFF WATER SUPPLY. REMOVE THE OLD
FAUCET AND FLEXIBLE HOSES. CLEAN SINK SURFACE
WITH A NON ABRASIVE CLEANER IN PREPARATION FOR
THE NEW FAUCET.
ENSURE THAT YOU USE PLUMBER'S
TAPE AND DO NOT OVER TIGHTEN THE
SUPPLY LINE NUTS AS THIS COULD
CAUSE PRODUCT FAILURE LEADING
TO WATER DAMAGE.
!
2. THREAD FEMALE END OF METAL
BRAIDED HOSES TO THE FAUCET (2).
7. AFTER INSTALLATION IS COMPLETE, TURN ON THE WATER SUPPLY AND ALLOW BOTH
HOT AND COLD WATER TO RUN SEPARATELY FOR AT LEAST TWO MINUTE EACH. WHILE
WATER IS RUNNING, CHECK FOR LEAKS. IT IS IMPORTANT TO VIEW THE CONNECTIONS AT
THE MALE AND FEMALE FLEXIBLE HOSE CONNECTIONS. IF LEAKS ARE DETECTED, REFER
BACK TO THE INSTRUCTIONS AND ADJUST ACCORDINGLY. TIGHTENING NUTS SLIGHTLY MAY
STOP ANY MINOR LEAKS.
6. ATTACH THE FEMALE CONNECTIONS OF THE FLEXIBLE HOSES TO
THE COLD AND HOT WATER SUPPLY .
5. (IF NOT DONE ALREADY) ATTACH SPRAYER TO FEMALE
CONNECTION OF SPRAYER HOSE BY HAND AND TIGHTEN UNTIL
SECURE. MAKE SURE THE BLACK WASHER WITH SCREEN IS
SEATED AND INSTALLED PROPERLY.
!
ENSURE THAT PARTS ARE ASSEMBLED IN THE
ORDER AS DEPICTED IN DIAGRAM TO PREVENT
DAMAGE TO FAUCET AND SUPPLY LINES.
3. POSITION THE PARTS IN THE COUNTERTOP HOLE
AS DEPICTED. FROM BENEATH THE COUNTERTOP
HOLE ASSEMBLE THE PLASTIC HOLDER, RUBBER
RING, AND METAL PLATE IN THE ORDER DEPICTED IN
THE DIAGRAM. FROM ABOVE THE COUNTERTOP YOU
WILL SCREW THE TWO LONG SCREWS INTO THE
METAL PLATE BELOW. MAKE SURE THE SCREW
HOLES ALL LINE UP BEFORE DRILLING.
PLATE
STABILIZES FAUCET
UNDER COUNTERTOP
!
ENSURE THAT YOU USE PLUMBER'S TAPE AND ADJUSTABLE WRENCH,
DO NOT OVER TIGHTEN AS THIS COULD CAUSE PRODUCT FAILURE
LEADING TO WATER DAMAGE.
! USE WASHER WITH SCREEN AT CONNECTION POINT BETWEEN SPRAYER AND SPRAYER HOSE. THIS
WILL STOP DEBRIS FROM TRAVELING INTO THE SPRAYER HEAD AND EFFECTING ITS
FUNCTIONALITY. PLEASE NOTE THAT THE SCREEN WASHER WILL NEED TO BE REMOVED AND
CLEANED APPROXIMATELY ONCE EVERY 3 MONTHS TO AVOID BUILD UP AND LOW WATER FLOW.
SCREWS
COPPER
PIN
SCREWS
COUNTERTOP
4. PLACE THE FAUCET ON TOP AND
SECURE WITH THE SET SCREW.
4
COUNTERTOP
PLATE
SET SCREW