VIGO VG06041 Скачать руководство пользователя

Страница: 21 / 22

MODEL VG06041

The small hex

hole on on the
roller will be

facing up on this

roller.

ROLLER (3)

WALL

STRAIGHT WALLS

ROLLER "A"
SMALL HEX HOLE
DIRECTION

ROLLER "B"
SMALL HEX HOLE
DIRECTION

WALL DIRECTION

STRAIGHT WALL

WALL OUT OF

PLUMB

WALL

TOP ANGLED WALL

TILTS IN AT TOP
(EXAGGERATED

FOR PURPOSE
OF DEPICTION)

FIG. 3

FIG. 2

The small hex
hole on on the
roller will be

center right on
this roller.

ROLLER (3)

The small hex
hole on on the
roller will be
facing up on this
roller.

ROLLER (3)

The small hex
hole on on this
roller will be
adjusted to meet
the gap.

ROLLER (3)

ROLLER "A"
SMALL HEX HOLE
DIRECTION

ROLLER "B"
SMALL HEX HOLE
DIRECTION

WALL DIRECTION

TOP ANGLED

ADJUST AS NEEDED

BOTTOM ANGLED WALL

ROLLER "A"
SMALL HEX HOLE
DIRECTION

ROLLER "B"
SMALL HEX HOLE
DIRECTION

WALL DIRECTION

BOTTOM ANGLED

FIG. 4

WALL OUT OF

PLUMB

WALL

TILTS IN AT

BOTTOM
(EXAGGERATED
FOR PURPOSE
OF DEPICTION)

ADJUST AS NEEDED

The small hex
hole on on the
roller will be
facing up on this
roller.

ROLLER (3)

The small hex

hole on on this
roller will be
adjusted to meet

the gap.

ROLLER (3)

Содержание VG06041























Результаты поиска

Содержание VG06041

Отзывы:

Похожие инструкции для VG06041

Бренды по названию

Популярные бренды

VIGO VG06041, Руководство по установке

Результаты поиска

Содержание VG06041

Отзывы:

Похожие инструкции для VG06041

Бренды по названию

Популярные бренды