background image

Pivot Door

Instruction Manual
N2F

IMPORTANT INFORMATION

Be aware toughened glass can shatter if not handled correctly. It should not 

be subjected to any sharp impact and it is essential to protect the glass by 

resting it on a soft protective surface during installation such as cardboard 

or carpeting. It is recommended to wear PPE at all times during installation.

Please make sure the purchaser/end user 

completes and returns the guarantee card 

which is enclosed with this product.  Failure 

to validate the Guarantee will mean only the 1 

Year Statutory Guarantee will apply.

CONSUMER GUARANTEE

PRE-INSTALLATION CHECKS

1.  Check you have the correct product.  Please look at the labels on the side of the product packaging.

2. 

Check all the product components are in the box and the fixing kits.

3.  Unpack your product and handle it with care.

4.  Please check the product for defects or damage, once the installation has commenced we cannot accept responsibility for any defects or damage.

5.  Please take time to read these instructions prior to installing your product.

6.  Before you commence any drilling check there are no hidden electrical cables and/or water pipes.

7.  No attempt should be made to re-work the toughened safety glass.

8.  The installation of the product should be performed by two persons.

9.  It is strongly recommended that the walls the product is going to be installed on are vertical.

10. 

It is strongly recommended the product is fitted on a tiled surface or similar waterproof surface.

11.  It is strongly recommended the walls are tiled and grouted before the product is installed.

12.  If the walls and/or the tray are not level you will not achieve maximum adjustment of the product.

13.  Pictures used are for illustration purposes only, product designs may alter slightly as a result of continuing product development.

14.  We do not stipulate where the European Standard Kite Mark should be positioned on the glass when being factory assembled.

15.  Please note that some natural misting may occur when you remove this product from its packaging, due to the addition of the glass protection pre-

coating. If this does occur this can easily be removed with a soft, dry cloth.

Ref: N2F REV2 - SEPT 2019

Component Check List: Supplied

Description

Quantity

Wall Profiles

2

Pivot Door

1

Screw Covers with Adhesive Tape

2

Frame and Door Magnets

1 of each

Vertical Frame (Magnet Side)

1

Dam Mouldings (Left and Right Hand)

1 of each

Bottom Rail Joiner (Left and Right Hand)

1 of each

Handle Assembly

1

Bottom Rail and Bottom Seal

1 of each

Fixing Kit Components

Description

Quantity

2.5mm Drill Bit

1

Wall Plugs

6

40mm screws

6

9mm Screws

10

Top Caps

3

3mm Allen Key

1

4mm Allen Key

1

Door Setting Block

1

Branding Badge

1

Equipment Check List: Not Supplied

Description

Electric / Battery Drill
6mm Masonry Drill Bit
Sealant Gun
Bathroom Sealant
Screwdriver
Spirit Level
Tape Measure
Pencil
Stanley Knife / Snips

Содержание N2F7613S










Отзывы: