background image

Step 2 - Fitting the Wall Profiles

1. 

Decide which side of the alcove the pivot side of the enclosure is to be fitted. Place the longer Wall Profile 

15mm in from the outside of the tray. The longer leg of the Wall Profile must be on the outside of the 

enclosure, towards the front of the tray. Make sure the Wall Profile is completely vertical using a spirit 

level and mark the wall through the slots with a pencil.

2. 

Drill the wall with a 6mm Masonry Drill Bit (not supplied) where the Wall Profile is to be positioned. Fit the 

Wall Plugs supplied (if going in to a brick or block wall). If going into a plasterboard wall you will need to 

purchase appropriate wall fixings. Wipe clear all debris from the Tray before referring to the next stage.

3. 

Where the Wall Profile is to be positioned on the Tray, place a bead of Bathroom Sealant (not supplied) 

the width of the Wall Profile along the tiled wall. Screw the Wall Profile to the wall with 40mm Screws 

(supplied). Do not over tighten the screws into the Wall Profiles as this will misshape the Wall Profile. 

Ensure the Wall Profile stays completely vertical throughout this procedure using a Spirit Level.

•  Failure to carry out this procedure correctly can result in serious water damage and is not covered by 

the Guarantee.

•  No sealant to be present between the Wall Profiles and the tiled walls vertically prior to screw fixing.

4. 

Seal the gap on the inside between the Tray and Wall Profile with a Bathroom Sealant (not supplied). 

•  Failure to carry out this procedure correctly can result in serious water damage and is not covered by 

the Guarantee.

5. 

Repeat these steps for the shorter Wall Profile on the opposite wall.

IMPORTANT: This product features two different length Wall Profiles. See notes below.

Short Leg

Long Leg

Содержание N2F7613S










Отзывы: