background image

Step 1 - Preperation

1.  Ensure the tray is completely level and check for any movement by standing in it - correct as necessary.

•  Please ensure that the tray is installed as per the manufacturers instructions.

2.  Seal the tray fully along the tiled walls prior to installation with a bathroom sealant (not supplied).

•  Prior to fitting the enclosure and when the sealant has fully cured, spray the shower handset over the 

joints and check for any leaks.

3. 

IMPORTANT: Prior to installing/attempting to fit the Pivot Door into an alcove measure the opening at 

the top, middle and bottom after all tiling and grouting has been done. Check this against the dimensions 

given in the table shown above to see if your alcove meets the criteria.

•  Check the plumbing for leaks.

•  Do not plasterboard over the tray.

•  Do not grout the tiles when the enclosure has been fitted as the grout may discolour the aluminium.

Product Code Minimum Alcove Size Maximum Alcove Size

N2F7613S

710mm

750mm

N2F813S

750mm

790mm

N2F913S

850mm

890mm

Measure at the top, 

middle and bottom.

The dimensions must 

meet the ones given 

in the table below for 

the respective product 

size.

NOTE: The Pivot Door is designed to fit into an alcove between two tiled walls (as shown below).

Содержание N2F7613S










Отзывы: