manualshive.com logo in svg

Vigilant LT0554, Руководство по установке и эксплуатации

Поделиться
Скачать
Vigilant LT0554 Скачать руководство пользователя страница 24

Vigilant BOWS Installation & Operation Manual 

 

Document: LT0554 

 

Page  

6 September 2012 

Issue 1.20 

4-2 

Use antistatic precautions when handling the circuit boards.

 

 

This is a Class A product.  In a domestic environment this product may 
cause radio interference, in which case the user may be required to take 
adequate measures.

 

 

                                430  

                      │                                 │ 
                      │                                 │ 
                  ┌─────────────────────────────────────────┐ ─── 
                  │   │                                 │   │     102  
                  │   │                                 │   │       
   ───────────────│── o ─────────────────────────────── o ──│──── 
                  │   │o

/6.0                         o

/6.0│   │    

                  │   │                                 │   │    
                  │   │                                 │   │    
                  │   │                                 │   │    
                  │   │                                 │   │    
                  │   │                                 │   │    
                  │   │                                 │   │     280  
                  │   │                                 │   │       
                  │   │                                 │   │    
                  │   │                                 │   │       
                  │   │                                 │   │    
                  │   │                                 │   │    
                  │   o ─────────────────────────────── o ──│──── 
                  │    o

/6.0                         o

/6.0    │ 

      1750 (MAX)  │                                         │ 
                  └─────────────────────────────────────────┘ 
      1220 (MIN)                                           
       
       
       
                           ALL DIMENSIONS IN MILLIMETRES 
       
       
       
       
                                FINISHED FLOOR LEVEL 
▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄ 
/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 

 

Figure 13. BOWS Cabinet Mounting Details 

 
 
 
 

 
 
 

 

 

 

Содержание LT0554











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды