ViewSat VS9000HD Скачать руководство пользователя страница 7

(13) SWITCHES:   

from left to right:

DISHPRO DPP-44 Switch

 allows you to pick up to 4 satellite locations and distribute them to up to 4 DISH 

Network Receivers. Power inserter included.

• In addition when used with the DP Separator (purchased separately) enables you to run 1 cable into the 
home and feed dual tuner DISHPro Receivers (921, 721, 522 and 322) making installations a snap 
• Built in DISH Pro Adaptor which will allow this switch to be used with any DISH Network receiver 
including older legacy equipment. 

DISHPRO DP-34 Switch

 Works with Dish 300 and Dish 500 satellite systems. Can be used to cascade 

additional DP34 multi switches for more receiver outputs. Can only be used with DishPro LNBFs.

• Switch has 3 trunk outputs for cascading to an additional DP34 switch for more outputs 
• Can be used indoors or outdoors 
• Does not require power insertion / power supply 
• Four outputs for connection to up to four DISH Network satellite receivers 
• ree satellite inputs for use with up to three orbital locations  

e first switch in the new DishPro Technology series of LNBFs and switches 

DISHPRO DP-21 Switch

 Two inputs for use with up to three orbital locations - 1 tuner output - Can be 

used with a DishPro Twin (or DishPro Quad LNBF) and a DishPro Single LNBF to provide three orbital 
locations to one tuner.

• Can be used indoors and outdoors 

Does not require power insertion 

Zinwell Multi-switch

 Model SAM4402-3A is designed to distribute 2 Polarizations (usually RHCP and 

LHCP or V/H) from 2 satellites to up to 4 IRDs. Polarization selection is by 13V/18V LNB voltage switching.

• is unit is powered by the receivers 
• Works great with the Channel Master Gain Master dish 
• Do not put any Termintators on any input/output ports 
• Use this device to hook up four receivers to a two satellite dish (with 4 coax connections) or to two dual- 
LNB dishes where each dish is pointed at a separate satellite 

Provides signals from two satellites to up to four receivers 

NOTE: Problems with Switchers are Connectors, wrong Connection, Power Inserters, Voltage, they 
just go bad.

Document page.7

VIEWSAT 9000HD User Troubleshooting Guide & Manual.    April /2008

Содержание VS9000HD




















Отзывы: