Viessmann VITOTRONIC 300 GW2 Скачать руководство пользователя страница 45

Страница: 45 / 146

Installation

Connections of combustion air device adaptor (VD2/VD2A/CT3 only)

Connection of the Combustion Air
Device Adaptor

Disconnect power to control and

burners.

Install Combustion Air Device

Adaptor, Part No.: 7134 563
on DIN Rail inside connection
enclosure (refer to installation
manual of Combustion Air
Device Adaptor).

Remove jumper between

terminals 16 and 17.

Make connection as shown in

the diagram.

Wire BK2 must be connected to
terminal 16 and BK3 to terminal
17 - DO NOT reverse.

Combustion Air Device Adaptor

DIN Rail in connection enclosure

Connection of the combustion air
blower to adaptor

Rated voltage:

120 VAC

Rating current:

max 5 FLA

Recommended connection
wire size:

AWG 14

Note:

Assure that combustion air blower
device is suitable for this application.

For detailed instruction on
adaptor installation, please refer
to the adaptor’s installation manual.

1. Make connection as shown in

the diagram at left.

Combustion Air Device Adaptor
in connection enclosure

Combustion air blower motor

Proving switch - “normally open”
rated for 120 VAC

Power supply, 120 VAC

5285

941

IMPORTANT

Provide disconnect means and

overcurrent protection as required

by local codes.

CAUTION

Содержание VITOTRONIC 300 GW2



















































































































































Результаты поиска

Содержание VITOTRONIC 300 GW2

Отзывы:

Похожие инструкции для VITOTRONIC 300 GW2

Бренды по названию

Популярные бренды

Viessmann VITOTRONIC 300 GW2, Инструкция по установке и обслуживанию

Результаты поиска

Содержание VITOTRONIC 300 GW2

Отзывы:

Похожие инструкции для VITOTRONIC 300 GW2

Бренды по названию

Популярные бренды