background image

3

Vitorond 200, VD2A Series Installation

5354 788 - 03

WARNING

Inhaling of fiberglass wool and/or ceramic fiber 

materials is a possible cancer hazard. These materials 

can also cause respiratory, skin and eye irritation.

 

H

Fiberglass wool and ceramic fiber materials

WARNING

Appliance materials of construction, products of 

combustion and the fuel contain alumina, silica, heavy 

metals, carbon monoxide, nitrogen oxides, aldehydes 

and/or other toxic or harmful substances which can 

cause serious injury or loss of life and which are 

known to the State of California to cause cancer, 

birth defects and other reproductive harm. Always 

use proper safety clothing, respirators and equipment 

when servicing or working nearby the appliance.

The state of California has listed the airborne fibers of 

these materials as a possible cancer hazard through           

inhalation. When handling these materials, special care 

must be applied.

Suppliers of fiberglass wool products recommend the  

following precautions be taken when handling these  

materials:

Precautionary measures

- Avoid breathing fiberglass dust and contact with 

  skin and eyes.
- Use NIOSH approved dust/mist respirator.
- Wear long-sleeved, loose fitting clothing, gloves 

  and eye protection.
- Wash work clothes separately from other clothing.  

  Rinse washer thoroughly.
- Operations such as sawing, blowing, tear-out and  

  spraying may generate airborne fiber concentration  

  requiring additional protection.

First aid measures

- If eye contact occurs, flush eyes with water to    

  remove dust. If symptoms persist, seek medical    

  attention.
-  If skin contact occurs, wash affected areas gently  

  with soap and warm water after handling.

 

H

Hazardous materials

Safety

 

Safety, Installation and Warranty Requirements 

(continued)

Suppliers of ceramic fiber products recommend the  

following first aid measures:

Respiratory tract (nose and throat) irritation:

  

  If respiratory tract irritation develops, move the    

  person to a dust free location.
-

 Eye irritation:

 If eyes become irritated, flush 

  immediately with large amounts of lukewarm water 

  for at least 15 minutes. Eyelids should be held away  

  from the eyeball to ensure thorough rinsing. 

  Do not rub eyes.

Skin irritation:

 If skin becomes irritated, remove soiled  

  clothing. Do not rub or scratch exposed skin. 

  Wash area of contact thoroughly with soap and water.  

  Using a skin cream or lotion after washing may be  

 helpful.

Gastrointestinal irritation:

 If gastrointestinal tract   

  irritation develops, move the person to a dust free  

 environment.

Содержание VITOROND 200 VD2A-125









































Отзывы: