Viessmann Vitodens 222-F B2TB Скачать руководство пользователя страница 40

Страница: 40 / 52

Vitodens 222-F, B2TB

Application 4 Operational Setup Instructions

The coding parameters described above are modified in

level 2 coding.

Step1

To access this coding you must hold the "OK"

key and "ext. Menu" key together for 5 seconds. This
gives access to the service level.

Step 2

: Hold the "OK" key and "Return" key for 5

seconds. This gives access to level 2 coding.

External Changeover- A function in which a contact

from an external device forces the boiler into a standby/
setback mode.

External Demand- A function in which a contact from

an external device forces the boiler to target a specific

water temperature. This overrides any/all outdoor reset

curves until the external contact re-opens.

Notes/Comments

In this application there are 2 heat circuits which operate at different temperatures. This particular drawing

portrays HC1 is a low temperature circuit, and HC2 is a Mid/High temperature circuit. Although there are

many different configurations, the setup below will operate HC1 as an on/off function (External Change-

over) using an outdoor reset curve, and HC2 as a constant set point temperature (External Demand). It is

important to provide a method of protecting the HC1 from high water temperatures when HC2 is operat-

ing, so don't forget to include the thermostatic mixing valve. To setup the boiler for this application you will

need to complete the following:

Type/Option

Step #

Description

Parameter

Set to:

Setup

Location

Set DHW Temperature

Set in heating

sub menu

HC1

Programming

Designate 28/20 Contact as HC1 Pump(P4)

:02

Set in Level 2

Coding

Conﬁgure boiler to operate upon a call for heat from HC1

Activates DE1 Contact

:01

Initiates Changeover

:01

Identiﬁes changeover based on DE1 contact

:01

Time limit for changeover

Set Pump Post Purge Time

# of Minutes

Temperature Limit for disabling changeover

-61

Turns off boiler circulator upon completion of call for heat

:-9

:01

Note: This disables the Frost Protection function.

Setup HC1 Outdoor Reset Curve

Set in heating

sub menu

Adjust Daytime schedule

--:--

Set Reduced room temperature

3ºC

External

Demand

Programming

Conﬁgure boiler to operate as an External Demand from HC2

Set in Level 2

Coding

(Ext. Demand)

Set desired setpoint temperature

Set Temp.

Identify DE2 as external demand contact

:02

Internal Circulator stays in control mode during
"External Demand"

:02

Optional Adjustments

Set a Heating Schedule

Set in heating

sub menu

Set an individual DHW Schedule

Conﬁgure P1 to shut down once low loss header has reached its setpoint temperature

51:

:01

Set in Level 2

Coding

Содержание Vitodens 222-F B2TB





















































Результаты поиска

Содержание Vitodens 222-F B2TB

Отзывы:

Похожие инструкции для Vitodens 222-F B2TB

Бренды по названию

Популярные бренды

Viessmann Vitodens 222-F B2TB, Инструкция по применению

Результаты поиска

Содержание Vitodens 222-F B2TB

Отзывы:

Похожие инструкции для Vitodens 222-F B2TB

Бренды по названию

Популярные бренды