background image

Safety/General Information

5

Important Regulatory and Installation Requirements

(Continued)

Technical literature

Literature applicable to all aspects of

the Vitocell:
- Technical Data Manual

- Installation Instructions
- Start-up/Service Instructions

- Operating Instructions

and User’s Information Manual

Leave all literature at the installation
site and advise the system
operator/ultimate owner where the
literature can be found. Contact
Viessmann for additional copies.

About These Instructions

Take note of all symbols and notations intended to draw attention to potential hazards or important product information.
These include ”WARNING”, ”CAUTION”, and ”IMPORTANT”. See below.

Warnings draw your attention to the
presence of potential hazards or
important product information.

Cautions draw your attention to the
presence of potential hazards or
important product information.

Helpful hints for installation, operation
or maintenance which pertain to the
product.

This symbol indicates that additional,
pertinent information is to be found in
column three.

This symbol indicates that other
instructions must be referenced.

Product Information

42 and 53 USG / 160 and 200 ltr capacity
Indirect-fired domestic hot water storage tank with one heat exchanger coil for use
with hot water heating boilers.

92 and 120 USG / 350 and 450 ltr capacity
Indirect-fired domestic hot water storage tank with one heat exchanger coil for use
with hot water heating boilers, commercial heating plants, and low-temperature
heating systems (larger heating surface).

5167

535

v1

.2

Indicates an imminently hazardous

situation which, if not avoided, could

result in death, serious injury or

substantial product/property damage.

WARNING

Indicates an imminently hazardous

situation which, if not avoided, may

result in minor injury or

product/property damage.

CAUTION

IMPORTANT

5167

535

v1

.2

Содержание Vitocell 300 EHA Series

























Отзывы: