Videx VX2300 Скачать руководство пользователя страница 30

Страница: 30 / 100

67009600-EN - Edition 2015 - Rev. 1.0

VX2300 Digital System - “2 Wire” Audio/Video Door Entry System

VX2300 Digital System - Installation handbook

Art. SL5488N

Slim hands free videomonitor

MELODY SELECTION

• When in the programming mode, press left or right call tone volume control buttons

(press the left button to navigate back-

ward or the right button to navigate forward in the melodies selection menù) until the videomonitor plays the selected melody

(during the melody play the LED1 stops flashing).

• Before press again one of the two buttons to select previous (left button) or next (right button) melody, wait for LED1 starts

flashing again then press and hold pressed one button until the selected melody is played.

• Once reached the required melody, Wait approx 10 seconds for LED 1 to stop flashing to signal that the new value is stored and

program mode has exited.

NOTES

The second melody increases its volume at each ring: first ring starts at minimum volume level up to the maximum volume level on the

last ring. Are available 4 levels of volume: if are set 6 rings, the fourth, the fifth and the sixth will be emitted at the maximum volume level.

VIDEOPHONE ADDRESS – SW1.1..8

SW1.1..8

The table above shows how to set the address of the videophone. Considering that ON = 1 and OFF = 0, multiply

each digit for the relevant decimal weight then sum values obtained to get the address: E.g. as highlighted in the

table OFF,ON,OFF,OFF,ON, OFF,ON in binary is equal to 0100101 then multiplying each digit for the relevant dec-

imal weight you obtain the address that is 37.

SWITCHES STATUS

BINARY CODE – DECIMAL WEIGHT

ADDRESS

128

OFF

255

NOTES

The maximum number of units allowed is 100 but the address of each unit can be a value between 1 and 255.

BUS TERMINATION – SWITCH SEL1

SEL1

Term.ON

SEL1

Term.OFF

The factory preset for this switch is

“Term.ON”: termination enabled. In

case of more units (intercoms, vide-

ophones or videomonitors) in a par-

allel connection (bus wires are connected to the terminals of

the first unit then from this to the second and so on up to 4 units

max) SEL1 must be set to “Term.ON” only for the last unit in the

chain while on all other units must beset to “Term.OFF” (bus ter-

mination disabled).

USING WITH ART. 317 – JP1

JP1

Without

Art. 317

JP1

With

Art. 317

The factory preset for this jumper is

open: Videophone not connected to

the Art. 317. If the videophone is con-

nected to an old Art. 317 video distri-

bution box, this jumper must be

closed.

INTERCOMMUNICATION MODE – SW3.1

SW3.1

This switch establishes the intercommunication mode: in OFF position (default) intercommunication is between units

in the same apartment (same addresses but different extension); in ON position the intercommunication is between

units in different apartments (different addresses).

On installations where there are more than one intercom/videophone in the same apartment and intercommunication

between different apartments is required, only one intercom/videophone may be set with this function (SW3.1=ON,

SW3.2=OFF, SW3.3=OFF). The other intercom/videophones in the apartment must be set for local intercommunication with

extension addresses “2-4” (slaves). From the intercom/videophone set for intercommunication with other apartments it

will be not possible to intercommunicate within the apartment but slave extensions 2-4 will be able to intercommunicate

with each other.

Содержание VX2300





































































































Результаты поиска

Содержание VX2300

Отзывы:

Похожие инструкции для VX2300

Бренды по названию

Популярные бренды

Videx VX2300, Руководство по установке

Результаты поиска

Содержание VX2300

Отзывы:

Похожие инструкции для VX2300

Бренды по названию

Популярные бренды