Videx 2301N Kristallo Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 60

background image

VX2300 2 Wire Video Digital System

PrtCode:VX2300_2_9.doc – Pag.31

08/03/2011

Rev.2.9

Art.2315

BUS booster and video signal amplifier

BUS IN

PS

H

L

M

BUS OUT

AMPLIFICATION

Fig.1

Fig.2

DESCRIPTION

The Art.2315 restores the voltage levels of the BUS line and amplifies the video signal (3 levels: H=high, M=medium and L=low). The BUS line must be
interrupted and connected to the BUS-IN input, then the signal from the BUS-OUT will be amplified. Connect to the PS input a power supply Art.2321.

We suggest the use of the BUS booster in installations which are not using the VIDEX CM2 cable and it is necessary to reach large cables distances.
(i.e. Using CAT5, distances greater than 70m).

CONNECTION TERMINALS AND JUMPERS
Terminal/Jumper Description
BUS IN

BUS line input

BUS OUT

BUS line output

PS

Power supply input (use Art.2321)

AMPLIFICATION

Video signal amplification, 3 levels = high, medium and low

SPECIFICATION

Housing/Mounting

Plastic box 50x60x20mm / direct wall mounting

Push Buttons

N/A

Programming

N/A

Controls

Video signal amplification (3 levels)

Power Supply

Requires local 2321 PSU.

Working Temperature

-10 +50ºC

CUSTOMER SUPPORT INFORMATION

All Countries Customers

UK Customers

VIDEX Electronics S.p.A.

www.videx.it

–

[email protected]

Tel.+39 0734 631669

Fax +39 0734 632475

VIDEX Security LTD

www.videx-security.com

Tech Line 0191 224 3174

Fax 0191 224 1559

The product is CE marked demonstrating its conformity and is for distribution within all
member states of the EU with no restrictions.
This product follows the provisions of the European Directives
89/336/EEC & 92/31/EEC (EMC),
73/23/EEC (LVD) and 93/68/EEC (CE marking).

Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere distribui-
to liberamente all’interno dei paesi membri dell’unione europea EU.
Questo prodotto è conforme alle direttive Europee
89/336/EEC & 92/31/EEC (EMC),
73/23/EEC (LVD) e 93/68/EEC (Marcatura CE).

«
...
29
30
31
32
33
...
»

Содержание 2301N Kristallo Series





























































Отзывы:

Нет отзывов

Похожие инструкции для 2301N Kristallo Series

Бренд: Yamaha Страницы: 24

Бренд: Harman Страницы: 10

Бренд: QSC Страницы: 2

Бренд: QSC Страницы: 2

Бренд: QSC Страницы: 16

Q-SYS Core 110f

Бренд: QSC Страницы: 2

Бренд: QSC Страницы: 4

Aventage RX-A3040

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 8

Бренд: Panasonic Страницы: 4

Бренд: Turbosound Страницы: 13

Бренд: EAW Страницы: 2

Бренд: M-system Страницы: 5

SupplyNet DS21-24

Бренд: Viking Страницы: 2

Бренд: Kelvinator Страницы: 16

Бренд: DAEWOO ELECTRONICS Страницы: 34

Бренд: Tews Technologies Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды