manualshive.com logo in svg

Victron energy Lynx Ion BMS 1000A, Руководство пользователя

Поделиться
Скачать
Victron energy Lynx Ion BMS 1000A Скачать руководство пользователя страница 17

 

 

 

8 LED INDICATIONS 

Firmware version 1.XX and higher. 

Status LED state 

Description 

Off 

System is in standby mode. Press START button to start up the system 

On 

Running 

Blinking 

Updating firmware of connected batteries 

Flashing/beeping 2 times 

Battery communication error (check BMS CAN-Bus cables) 

Flashing/beeping 3 times 

Under or overvoltage detected (check charger or load settings) 

Flashing/beeping 4 times 

Under or over temperature detected (check battery temperatures) 

Flashing/beeping 5 times 

Pre-charge time out occurred (check if pre-charge current is below 10A) 

Flashing/beeping 6 times 

Pre-charge fuse broken (check the pre-charge fuse) 

Flashing/beeping 7 times 

Battery configuration failure (check BMS CAN-Bus cables) 

Flashing/beeping 8 times 

N.A. 

Flashing/beeping 9 times 

Battery firmware updating failure (contact manufacturer) 

Flashing/beeping 10 times 

Main safety contactor failure (contact manufacturer) 

Flashing/beeping 11 times 

Internal measurement failure (contact manufacturer) 

Flashing/beeping 12 times 

System instability problem detected (contact manufacturer) 

Flashing/beeping 13 times 

No appropriate firmware found for connected battery (contact manufacturer) 

 
9 MAINTENANCE

 

This product does not require specific maintenance. It will suffice to check all connections once a year. Avoid moisture and 
oil/soot/vapors, and keep the device clean. 

Содержание Lynx Ion BMS 1000A























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды