Victron energy Color Control GX Скачать руководство пользователя страница 29

Страница: 29 / 74

Item

Default

Description

GPS

Read full feature description [7]

GPS information

Status, Latitude, Longitude, Speed, Course, Altitude, Number of
satellites

Format

Select the format in which to show the Latitude and Longitude.

Speed unit

km/h

Choose between km/h, meters per second, miles per hour, or
knots.

Device

Connected, Connection, Product, Product ID, Firmware version,
Device instance

Generator start/stop

Configure generator autostart settings and conditions.

Read full feature description

State

Displays if the generator is running or not

Error

Displays if there is error (eg generator is supposed to be running
but no AC input is detected)

Total run time

Total time the generator has been running since reset.

Time to next test run

If a periodic run is programmed, this counter will display in days,
and hours how long before that will occur.

Auto start functionality

Enable or Disable the Autostart functions, this can be further
configured in the Generator -> Settings -> Conditions menu

Manual start

Start generator, Run for hh:mm

Daily run time

Submenu shows the history of time generator has been running
(minutes) each day for the previous 30 days.

Generator start/stop -> Settings

Generator start/stop -> Settings -> Conditions

On loss of communication

Stop generator

Stop, Start, Keep generator running

Do not run generator when
AC1 is in use

This option is ideal for back-up systems where a Quattro has
mains/grid electricity connected to its AC-in 1 terminal, and a
Genset connected to its AC-in 2 terminal. With this option
enabled, the Genset will only start after a mains failure.

Battery SOC

Use Battery SOC value to start/stop - No / Yes

Start when SOC is lower than - %

Start value during quiet hours - % (to override programmed quiet
hours when absolutely necessary)

Stop when Battery SOC is higher than - %

Stop value during quiet hours - % (allows for less runtime during
quiet hours, once system is recovered)

Battery current

Battery voltage

AC output

Use value to start/stop - No / Yess

Start when value is higher than - Amps / Voltage / Watts

Start value during quiet hours - Amps / Voltage / Watts (to
override programmed quiet hours when absolutely necessary)

Start after condition is reached for - seconds (to allow for
momentary spikes to pass without triggering start)

Stop when value is lower than - Amps / Voltage / Watts

Stop value during quiet hours - Amps / Voltage / Watts (allows for
less runtime during quiet hours, once system is recovered)

Stop after the condition is reached for - seconds (to allow for
momentary dips without stopping the running generator)

Inverter high temperature

Inverter overload

Start on value warning - No / Yes

Start when warning is active for - seconds (to allow for
momentary spikes to pass without triggering start)

When warning is cleared stop after - seconds (to allow for
momentary dips without stopping the running generator)

Generator start/stop -> Settings -> Conditions -> Periodic run

Color Control GX Manual

Page 25

Configuration

Содержание Color Control GX











































































Результаты поиска

Содержание Color Control GX

Отзывы:

Бренды по названию

Популярные бренды

Victron energy Color Control GX, Руководство пользователя

Результаты поиска

Содержание Color Control GX

Отзывы:

Бренды по названию

Популярные бренды