manualshive.com logo in svg

Victron energy Color Control GX, Руководство пользователя

Поделиться
Скачать
Victron energy Color Control GX Скачать руководство пользователя страница 13

Si-Sensor

Victron RS485 to USB interface

Signal

-

Black

Power Neg/Gnd - 0 VDC (not used)

Brown

Terminator 1 - 120R (not used)

Green

Terminator 2 - 120R (not used)

Installation Notes

The maximum DC power supply voltage permitted for the IMT Si-RS485 series solar irradiance sensor range is 28.0 VDC -
accordingly for 24 V and 48 V battery banks/systems an appropriate 

Victron DC-DC converter

 (24/12, 24/24, 48/12 or 48/24) or

AC-DC adaptor must be utilised in the installation.

For 12 V battery banks/systems the IMT Si-RS485 series solar irradiance sensor range may be powered directly from the battery
bank and will continue to operate down to minimum voltage of 10.5 V (as measured at the sensor, account for voltage drop in the
cable).

For detailed wiring/installation notes and specifications refer to the 

IMT Si-RS485 series solar irradiance sensor 'Quick Reference

Guide'

 and 

Victron RS485 to USB interface cable ‘Datasheet’

.

To ensure signal integrity and robust operation, particularly ensure that;

• Extension cabling complies with the minimum cross-sectional area specifications in the related table - dependent on DC supply

voltage and cable length

• Extension cabling has appropriate shielding and twisted pair cores
• The original cable attached to the Victron RS485 to USB interface is reduced to a maximum length of 20cm in installations

where the total cable length is over 10m or there are installation/site specific interference issues – in this case appropriate/high
quality cabling should be used for the entire cable length, rather than only for the extension length

• Cabling is installed separated/away from the main DC or AC power cabling
• All wiring is properly terminated (including unused wires) and properly isolated from weather/water ingress
• The sensor housing is not opened or tampered with during installation - as sealing integrity will be compromised (and warranty

void)

The IMT Si-RS485TC series solar irradiance sensor includes internal Galvanic Isolation (up to 1000V) between power supply and
RS485 Modbus circuits, accordingly the non-isolated Victron RS485 to USB interface is suitable for most installations.

However, if an isolated RS485 to USB interface is preferred the only compatible device is 

Hjelmslund Electronics USB485-

STIXL

 (any others type will not be recognised by the GX device).

Multiple Sensors

It is possible to connect multiple IMT Si-RS485 series solar irradiance sensors to a common Victron GX device, however a
dedicated Victron RS485 to USB interface is required for each individual unit.

Multiple units cannot be combined on a single interface (as this is not supported by the related Venus OS software).

Configuration

There is normally no need for any special/additional configuration – the default ‘as shipped’ configuration is compatible for
communication with a Victron GX device.

However, in cases where the IMT Si-RS485 series solar irradiance sensor has been previously used in another system and/or the
settings changed for any reason, it is necessary to restore the default configuration before further use.

To revise the configuration, download the 

IMT 'Si-MODBUS-Configuration software tool'

. Follow the instructions in the

 IMT ‘Si

Modbus Configurator Documentation’

. and check/update the following settings:

• MODBUS Address: 1
• Baud Rate: 9600
• Data Format: 8N1 (10 Bit)

For further support related to configuration of the IMT Si-RS485 Series irradiance sensors please contact IMT Solar directly.

User Interface - GX Device

Upon connection to the Victron GX device and power up the IMT Si-RS485 Series irradiance sensor will be automatically
detected within a few minutes and appear in the 'Device List' menu.

Color Control GX Manual

Page 9

Installation

Содержание Color Control GX











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды