Victory Motorcycles Vision Tour 2013 Скачать руководство пользователя страница 87

Страница: 87 / 134

Maintenance

Trunk Removal

1. Remove the seat. See page 83.
2. Disconnect the trunk wire harness.
3. Remove the license plate.
4. Remove the two 4 mm Allen screws from bot-

tom of the license plate bracket. Remove the
bracket.

5. Open the trunk and remove all contents.
6. Remove the compartment cover by squeezing

between the two notches.

7. Remove three of the four trunk mount bolts. Sup-

port the trunk before removing the last bolt.

Tool:

13 mm socket, extension, drive handle

8. Install the street trim panel. See page 84.

Trunk Installation

1. Remove the street trim panel. See page 84.
2. Reverse the trunk removal instructions to rein-

stall the trunk.

3. Tighten the trunk mounting bolts.

Torque: 26 ft-lbs (35 Nm)

4. Tighten the license plate bracket screws.

Torque: 36 in-lbs (4 Nm)

Remove Screws

Wire
Harness

Содержание Vision Tour 2013







































































































































Результаты поиска

Содержание Vision Tour 2013

Отзывы:

Похожие инструкции для Vision Tour 2013

Бренды по названию

Популярные бренды

Victory Motorcycles Vision Tour 2013, Руководство пользователя

Результаты поиска

Содержание Vision Tour 2013

Отзывы:

Похожие инструкции для Vision Tour 2013

Бренды по названию

Популярные бренды