Victory Motorcycles Hammer 8-Ball Скачать руководство пользователя страница 3

Страница: 3 / 96

WARNING

Improper vehicle use can result in SEVERE INJURY or DEATH.

NEVER Operate:

• If you are under the age of 16 and without a driver’s license with motorcycle endorsement

• Under the influence of drugs or alcohol

• Off-road

• With more than one passenger (motorcycle must be equipped with passenger foot pegs)

• With weight that exceeds maximum weight rating

ALWAYS:

• Wear a helmet, eye protection, gloves, long-sleeve shirt, long pants and over-the-ankle boots.

• Make sure any passenger reads and understands all safety labels.

• Be aware of your surroundings and driving conditions.

• Keep both hands on the handlebars and both feet on the footrests when riding.

• Use only genuine VICTORY accessories designed for your model.

READ RIDER’S MANUAL. FOLLOW ALL INSTRUCTIONS AND WARNINGS.

Safety Training
Safety training is a top priority for POLARIS. POLARIS strongly encourages you to take a motorcycle
rider education course in your area of operation.

ALWAYS USE AN

APPROVED HELMET

AND PROTECTIVE

GEAR.

NEVER USE WITH

DRUGS OR ALCOHOL.

Содержание Hammer 8-Ball

































































































Результаты поиска

Содержание Hammer 8-Ball

Отзывы:

Похожие инструкции для Hammer 8-Ball

Бренды по названию

Популярные бренды

Victory Motorcycles Hammer 8-Ball, Руководство пользователя для мотоциклиста

Результаты поиска

Содержание Hammer 8-Ball

Отзывы:

Похожие инструкции для Hammer 8-Ball

Бренды по названию

Популярные бренды