Victaulic Vic-300 MasterSeal 761 Series Скачать руководство пользователя | Manualshive

Страница: 14 / 35

background image

I-VIC300MS

/ Vic-300

®

MasterSeal

™

Butterfly Valves

/ Installation and Maintenance Instructions

2 . Loosen the set screw on the side of the handle (Item 1), as shown

above .

2a . Remove the Lever Lock Handle assembly from the plate .

NOTICE

• The stem contains a key that is essential for re-installation of a

handle or a gear operator. Use care to prevent misplacement of
this key.

3 . Remove the hex nuts (Item 5) and lock washers (Item 4) from the

two hex-head screws (Item 3) . In addition, remove the hex nut
(Item 5) and lock washer (Item 4) from the hex-head screw (Item
6) to permit removal of the plate from the valve body mounting
flange .

4 . Remove the plate (Item 2) from the valve body mounting flange .
5 . The valve is now ready for conversion to a Tamper-Resistant

Handle or a Gear Operator . In addition, the “Stem Seal
Replacement” instructions can be performed, the thermal barrier
kit can be installed, or the insulation extension kit can be installed .

CAUTION

• DO NOT attempt to operate a Series 761 or 461 Butterfly Valve

without a handle or gear operator installed.

Failure to follow this instruction will cause improper valve operation
and damage to the stem.

I-VIC300MS_13

victaulic.com

VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2014 VICTAULIC COMPANY. ALL RIGHTS RESERVED.

REV_F

«
...
12
13
14
15
16
...
»

Содержание Vic-300 MasterSeal 761 Series




































Отзывы:

Нет отзывов

Похожие инструкции для Vic-300 MasterSeal 761 Series

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

Бренд: Panamax Страницы: 16

Бренд: Bartlett Страницы: 7

Бренд: ZKTeco Страницы: 13

Бренд: UniPi Technology Страницы: 4

Бренд: brel-motors Страницы: 2

Бренд: HQ Power Страницы: 23

Бренд: Allen-Bradley Страницы: 16

Бренд: D+H Страницы: 2

Бренд: NXP Semiconductors Страницы: 39

NETBuilder II DPE 80

Бренд: 3Com Страницы: 32

Бренд: 4IPNET Страницы: 11

Бренд: C-TEC Страницы: 42

Бренд: Satel Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды