VICKING WORKmate II Скачать руководство пользователя страница 27

Страница: 27 / 45

Vicking electronics

Pag. 27

The workmate II keyboard output codes

List of functionkey codes The keyboard layout :

A B C D

Key

is the backspace key it is used to edit the numerical input, no code is send to the concentrator.

Key

is typically used to go back to the previous step in the dialog.

Key

didn’t exits in the older workmates. It can be used in combination with key A6 to walk through lists

and menus.
Key

is the enter key, to confirm a numerical input.

With the online concentrator the enter key has no code, you get only the address and the data.
Key

is the barcode key, this key is only use as a function key in the WORKmate II, in the older

workmates is was also used to abort the barcode reader mode.

posi-

tion

key

VIPRO

ONLINE

100

101

102

103

104

105

106

107

108

109

F10

110

F11

111

F12

112

F13

113

F14

114

F15

115

F16

116

↑

↓

117

only for

edit

only for

edit

barcode

121

↵

Содержание WORKmate II














































Результаты поиска

Содержание WORKmate II

Отзывы:

VICKING WORKmate II, Руководство пользователя, Страница: 27 / 45

Результаты поиска

Содержание WORKmate II

Отзывы: