Vetus DEUTZ DT44 Скачать руководство пользователя страница 51

Страница: 51 / 88

Remove the cap of the filler neck on the

top of the header tank.

Fill the cooling system.

Replace plug A as soon as coolant flows

out.

Use a mixture of 40% antifreeze (ethylene-

glycol based) and 60% tap water or use a

special coolant.

For specifications see page 72.

The level of the coolant must be at the

lower edge of the filler neck.

Replace the filler cap.

Bleeding will take place automatically dur-

ing filling!

After the engine has run for the first time

and has reached operating temperature

and has cooled down again to ambient

temperature, check the coolant level in the

heat exchanger housing.

If necessary, add coolant.

Caution!

Never fill the cooling system with sea

water or brackish water.

3 Maintenance

VD00473

VD00477

Calorifier

If a calorifier is connected to the engine

and this heater is positioned above the

upper side of the engine then bleeding of

the calorifier will not take place automati-

cally! Fill the calorifier separately to bleed

the cooling system completely.

☞

COOLANT

47 Filling the cooling system

Coolant replacement

Every 2000 operating hours.

OOLANT

4 C

.: 8.5 litres (1.9 UK gal)

QUANTITY

: 6 C

.: 12 litres (2.6 UK gal)

Содержание DEUTZ DT44
























































































Результаты поиска

Содержание DEUTZ DT44

Отзывы:

Похожие инструкции для DEUTZ DT44

Бренды по названию

Популярные бренды

Vetus DEUTZ DT44, Руководство по эксплуатации

Результаты поиска

Содержание DEUTZ DT44

Отзывы:

Похожие инструкции для DEUTZ DT44

Бренды по названию

Популярные бренды