Vetus DEUTZ DT44 Скачать руководство пользователя страница 36

Страница: 36 / 88

Engine oil change

Change the engine oil every 500 hours of

operation (together with engine oil filter

replacement).

If the engine runs less than 500 hours dur-

ing the year the oil should be changed at

least once a year.

Run the engine for a few minutes before

changing the oil; warm oil can be pumped

out more easily.

17 Draining the oil

The pump for the oil sump is (normally)

located at the heat exchanger side of the

engine.

As an option for twin engine installation,

the pump may be located on the other

side at one of the engines.

18 Removing the oil filter

Unscrew the oil filter, with a commercially

available tool, when all the oil has been

pumped out.

Catch any dripping oil.

Warning!

Beware of burns from hot oil.

4 Maintenance

Engine oil change

Every 500 operating hours.

VD00017

VD00023

Tip

Change the oil with a switched off engine

at operation temperature. (Lube oil tem-

perature approx. 80°C (176°F).)

Caution!

Used oil must be collected in a container

for proper disposal according to laws and

regulations.

☞

Содержание DEUTZ DT44
























































































Результаты поиска

Содержание DEUTZ DT44

Отзывы:

Похожие инструкции для DEUTZ DT44

Бренды по названию

Популярные бренды

Vetus DEUTZ DT44, Руководство по эксплуатации

Результаты поиска

Содержание DEUTZ DT44

Отзывы:

Похожие инструкции для DEUTZ DT44

Бренды по названию

Популярные бренды